Hallo
Da meine Dream den Geist aufgegeben hat,habe ich mir eine Dbox2 von Sagem zugelegt.Die soll mit einer Sky S02 Karte laufen.
Die box selber hat einen 600er Chip verbaut,
Nun zum Problem:
Die Box hängt an einer Multytenne,also 4 Satelitten werden angepeilt.
Aber ich kann nur sehr wenige Programme sehen bei den meisten Sendern kommt die Meldung "Kanal (zur Zeit)nicht verfügbar"
Tele5 und noch ein paar unwichtige Sender gehen, nur leider nicht die worauf es mir ankommt (Sky Sender).
Von Sky bekomme ich nur Nicktoons zu sehen.
Habe schon viele Einstellungen probiert.Disceq habe ich auf 1.0 stehen.
Mir gehts mit der Dbox nur um die Sender von Astra.
Vorgestern hatte ich sogar mal mehr Sender von Sky zu Gesicht bekommen.
Aber auch da wiederum nur wenige.Weis aber leider die genauen Einstellungen nicht mehr,die dort eingegeben waren.
Habe auch schon fertige Settings benuzt und auch die satellit.xml geändert per Totalkommander.
Habe auch grad wieder neu geflasht.
Vielleicht kann mir hier von euch jemand helfen der auch ne Sagem hat und auch das Problem hatte.Und mir mal seine Kompletten einstellungen verrät.
Hier mal ein Bootlog :
€kdebug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.3 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-6d.f1.4a.08.00.00-01
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0040
will verify ELF image, start= 0x800000, size= 154360
verify sig: 262
Branching to 0x40000
U-Boot 1.2.0 (Tuxbox) (Mar 11 2009 - 14:20:53)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.3
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ............. done.
env: found "console" with value ttyS0
env: found "baudrate" with value 9600
env: found "dbox_duplex" with value 0
env: found "lcd_inverse" with value 0
env: found "lcd_contrast" with value 15
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (jffs2) loading 'vmlinuz' to 0x100000
### FS load complete: 646305 bytes loaded to 0x100000
.................................................. ............. done
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 646241 Bytes = 631.1 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37-dbox2 (dbox@DboxCVS) (gcc version 3.4.6) #1 Di 17. Mär 14:5
6:46 CET 2009
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,9600 dbox_duplex=0 root=/dev/mtdblock2 rw roo
tfstype=jffs2
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30876k available (1096k kernel code, 336k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled<6>eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:3e
:49:d5
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 5 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.2.1 (2008.07.25-11:34+0000) multi-call Thu Jan 1 01:0
0:00 UTC 1970
info, udhcpc (v1.2.1) started
debug, Sending discover...
debug, Sending discover...
debug, Sending discover...
info, No lease, failing.
event: $Id: event.c,v 1.12 2003/09/30 0538 obi Exp $
tuxbox: no IDE-Interface detected
Detected STB:
Vendor: Sagem
Model: D-BOX2
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter - GLJ-Team (JohnDoe,g5401) (C-Cube AViA GTX/eNX wit
h AViA 500/600).
DVB: registering frontend - http://glj.6x.to 0:0 (VES1993)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 1920 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 1722 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_av_core: Starting avia_gt_wdt thread.
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Please press Enter to activate this console. [timerd] woke up from timer? false!
$Id: zapit.cpp,v 1.430glj 2009/04/08 14:00 GLJ-Team Exp $
[zapit] PMT update enabled
[frontend] uncommitted_switch_mode 0
ping: www.google.com: Host name lookup failure
ping: www.yahoo.com: Host name lookup failure
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 2 onid 85
/tmp/currentservices.xml: No such file or directory
$Id: controld.cpp,v 1.133 2009/02/24 19:09:09 seife Exp $
[controld] Boxtype detected: (3, Sagem D-BOX2)
[controld]: ROUTEVIDEO v1 = 0 a1 = 0 v2 = 0 a2 = 0 fblk=1
[controld] format: 4:3(LB)
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: cam_napi.c,v 1.8 2003/09/30 05
[EMU_START] Starte Camd2
[camd2] ca system id: 1702
lcdshot: /lib/libpng12.so.0: no version information available (required by lcdsh
ot)
lcdshot v0.7 GLJ-Team by JohnDoe based on lcshot by SnowHead
[nhttpd] Orginal Neutrino HTTP-Server starting. Developed GLJ-Team by JohnDoe w/
o y-Stuff v1.5d
[LCDFONT] initializing core...[camd2] no card is in slot #2
[camd2] a card is in slot #1
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
$Id: sectionsd.cpp,v 1.glj.1 Exp $
[camd2] ca system id: 1702
[camd2] card_country: GER
[camd2] card_number: 0276187693
[camd2] card_version: 0384
[sectionsd] Caching max 2500 events
[camd2] no card is in slot #2
[camd2] a card is in slot #1
[sectionsd] Caching 1 days
[sectionsd] Caching 1 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[basicsocket] send_data: Resource temporarily unavailable
[camd2] no card is in slot #2
[camd2] a card is in slot #1
[basicsocket] send_data: Resource temporarily unavailable
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
GLJ-Neutrino startet V3.80RT by GLJ-Team (JohnDoe)
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[camd2] no card is in slot #2
[camd2] a card is in slot #1
[camd2] no card is in slot #2
[camd2] a card is in slot #1
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] can not use input repeat on fd_rc[0]: 22 (Invalid argument)
[neutrino] setRepeat: delay=125 period=40 use kernel-repeat: no
[neutrino] received 4 sats
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[neutrino] initialized everything
[zapit] LOCK LOST! trying rezap... channel: 'kabel eins classics'
zap failed!
[zapit] LOCK LOST! trying rezap... channel: 'kabel eins classics'
[zapit] LOCK LOST! trying rezap... channel: 'kabel eins classics'
[sectionsd] getUTC: read: Connection timed out
[zapit] LOCK LOST! trying rezap... channel: 'kabel eins classics'
[zapit] LOCK LOST! trying rezap... channel: 'kabel eins classics'
[zapit] LOCK LOST! trying rezap... channel: 'kabel eins classics'
[zapit] LOCK LOST! trying rezap... channel: 'kabel eins classics'
[zapit] LOCK LOST! trying rezap... channel: 'kabel eins classics'
[zapit] LOCK LOST! trying rezap... channel: 'kabel eins classics'
[zapit] LOCK LOST! trying rezap... channel: 'kabel eins classics'
[sectionsd] getUTC: read: Connection timed out
Zitat von Satfan123
Alles da was da sein soll.Also war an der Sagem doch was kaputt.