Hi, du brauchst nur Oscam.

config
Code:
#
# main configuration
#
#[global]
#nice	      = -1
#WaitForCards  = 1
# logging
#pidfile	      = /var/run/oscam.pid
#logfile	      = /var/log/oscam/oscam.log
#usrfile	      = /var/log/oscam/oscamuser.log
#cwlogdir      = /var/log/oscam/cw
# monitor
#[monitor]
#port	      = 988
#aulow	      = 120
#monlevel      = 1
# web interface
#[webif]
#httpport      = 8888
#httpuser      = myusername
#httppwd       = mypassword
# protocols
#[newcamd]
#key           = 000102030405060708090A0B0C0D  hier kannst CCcam mit N-Lines verbinden
#port          = 10000@1722
#[radegast]
#port          = 20000
#user          = user1
#allowed       = 192.168.0.0-192.168.255.255
#[cs378x]
#port          = 30000@0100:FFFFFF;30001@0200:FFF000,FFFF00;30002@0300:FFFFFF
#[cccam]
#port          = 40000
#version       = 1.2.3     hier mit C-Lines
#build         = 1234
#reshare       = 2
#[gbox]
#password      = password1
#maxdist       = 4
#cardinfos     = card.infos
#ignorelist    = ignore.list
#onlineinfos   = online.infos
#locals        = 01000000,02000000,0300FFFF
#[serial]
#device        = user2@/dev/ttyS0?delay=1&timeout=300
[dvbapi]
enabled	      = 1    dadurch brauchst du keine CCcam auf der Dream, um damit zu gucken.
user          = user1   
demux         = /dev/dvb/adapter0/demux0
ca            = /dev/dvb/adapter0/ca1
socket        = /tmp/camd.socket
user account für dich
Code:
[account]
User       = user1
monlevel   = 4
uniq       = 0
group      = 1
AU         = 1
betatunnel = 1834.FFFF:1722    da müßen wir mal testen. 
caid = 1722
server
Code:
#===================================================
# /etc/tuxbox/config/oscam.server
#
# Prepared by PurpleHaze for Peter Pan Neverland 2.0
#===================================================
# Internal reader lower (or if the box has only one reader)
#----------------------------------------------------------
[reader]
label    = lower
protocol = internal
device   = /dev/sci0
enable   = 1
group    = 1
emmcache = 1,3,2
# For some NDS cards like CAID 093E you might need the boxkey.
#  Read the key from you original decoder and remove the last digit.
#  Convert from DEC to HEX. If the result is only 7 digits you must
#  add a zero in front. Insert the 8 digits below in stead of 00000000.
#boxid    = 00000000
# remote newcamd reader 
#[reader]
#label    = remote2
#protocol = newcamd
#key      = 
#device   =
#account  = 
#group    = 2
#fallback = 1
#[reader]
#label    = remote3
#protocol = newcamd
#key      = 
#device   = 
#account  = 
#group    = 3
#fallback = 1
# Internal reader upper (boxes with two readers)
#-----------------------------------------------
#[reader]
#label    = upper
#protocol = internal
#device   = /dev/sci1
#enable   = 0
#group    = 1
#emmcache = 1,3,2
# For some NDS cards like CAID 093E you might need the boxkey.
#  Read the key from you original decoder and remove the last digit.
#  Convert from DEC to HEX. If the result is only 7 digits you must
#  add a zero in front. Insert the 8 digits below in stead of 00000000.
#boxid    = 00000000
# Smargo (mousemode)
#  Set enable to 1 if connected to the box, 0 if not used
#--------------------------------------------------------
#[reader]
#label    = smargo
#protocol = mouse
#device   = /dev/ttyUSB0
#enable   = 0
#group    = 4
#emmcache = 1,3,2
# For some NDS cards like CAID 093E you might need the boxkey.
#  Read the key from you original decoder and remove the last digit.
#  Convert from DEC to HEX. If the result is only 7 digits you must
#  add a zero in front. Insert the 8 digits below in stead of 00000000.
#boxid    = 00000000