Hallo nochma.
Habe nun auch mal einen USB Hub dazwischen geschaltet und dann nochmal per Telnet einen Log gemacht:

usb 1-1: new high speed USB device using brcm-ehci and address 5
brcm-ehci brcm-ehci.0: port 1 high speed
brcm-ehci brcm-ehci.0: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
usb 1-1: default language 0x0409
usb 1-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1: Product: USB2.0 Hub
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
hub 1-1:1.0: usb_probe_interface
hub 1-1:1.0: usb_probe_interface - got id
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
hub 1-1:1.0: standalone hub
hub 1-1:1.0: ganged power switching
hub 1-1:1.0: global over-current protection
hub 1-1:1.0: Single TT
hub 1-1:1.0: TT requires at most 32 FS bit times
hub 1-1:1.0: Port indicators are supported
hub 1-1:1.0: power on to power good time: 100ms
hub 1-1:1.0: local power source is good
hub 1-1:1.0: no over-current condition exists
hub 1-1:1.0: enabling power on all ports
usb 1-1: link qh256-0001/a91e9100 start 255 [7/0 us]
hub 1-1:1.0: state 5 ports 4 chg 0000 evt 0000
hub 1-1:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 1-1:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
usb 1-1.1: new full speed USB device using brcm-ehci and address 6
usb 1-1.1: ep0 maxpacket = 8
usb 1-1.1: default language 0x0409
usb 1-1.1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.1: Product: FT232R USB UART
usb 1-1.1: Manufacturer: FTDI
usb 1-1.1: SerialNumber: xxxxxxxx
usb 1-1.1: hotplug
usb 1-1.1: adding 1-1.1:1.0 (config #1, interface 0)
usb 1-1.1:1.0: hotplug
usbserial_generic 1-1.1:1.0: usb_probe_interface
usbserial_generic 1-1.1:1.0: usb_probe_interface - got id
ftdi_sio 1-1.1:1.0: usb_probe_interface
ftdi_sio 1-1.1:1.0: usb_probe_interface - got id
ftdi_sio 1-1.1:1.0: FTDI FT232BM Compatible converter detected
usb 1-1.1: FTDI FT232BM Compatible converter now attached to ttyUSB0

So wie das aussieht sollte die Easymouse2 ja nun an ttyUSB0 laufen.
Wenn ich in der CCCam.cfg das einbringe: SERIAL READER : /dev/ttyUSB0
passiert trotzdem nichts. Was mache ich wohl noch falsch?

Gruß und Danke.