Soooo...
Wer von euch auch das wundervolle Neutrino auf der Kathi hat, und mgcamd einbauen möchte, hier mal meine configs.
Configs wurden angepasst. Alle CAID´s laufen. Dank an Reus!
1. Die mgcamd 1.35 aus diversen Foren laden, "mcgamd.sh4" nehmen, das ".sh4" entfernen und per FTP nach var/emu kopieren. (Rechte 755)
2. Die mg_cfg datei nach var/keys kopieren.
3. Die datei newcamd.list nach var/keys kopieren.# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 00 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30
# network ecm timeout in seconds
K: { 05 }
# newcamd dead routes connect retry, sec
Q: { 300 }
# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 02 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 11 }
# map all 180x nagra caids to 1801
# default is 01
F: { 00 }
4. ****Entfällt**** Die datei replace.list nach var/keys kopieren. (Angeblich wegen HD Kanälen. Da bei mir nur die CAID 1702 geht, kann ich leider nicht bestätigen...)CWS = 192.168.178.100 15000 HD-Kathi0 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15001 HD-Kathi1 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15002 HD-Kathi2 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15003 HD-Kathi3 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15004 HD-Kathi4 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
5. Die datei newcamd.conf nach var/tuxbox/config kopieren.# replace old with new {{ sid } { caid } { provid } { ecmpid } { newcaid } { newprovid } { newecmpid }}
# multivision 1 example
# R: {{ 515 } { 500 } { 7C00 } { A0 } { 500 } { 7800 } { A1 }}
# OR put this ecm on top if new* = 0
# R: {{ 515 } { 500 } { 7800 } { A1 } { 0 } { 0 } { 0 }}
# replace old caid > newcaid example
# X: {{ 624 } { 604 }}
X: {{ 1833 } { 1702 }}
# /var/tuxbox/config/newcamd/newcamd.conf
#
# newcamd mandatory settings
#
# Use emulator?
EMU = no
# if both control word server and emulator keys are available for the
# channel, which method should be tried first?
PREFER_EMU = no
# Autoupdate for Emu and Control Word Servers
# AU is always yes if there are betad UDS control word server
# connected to newcamd
AU = yes
#
# OSD
#
# number of seconds to show the newcamd OSD, works on enigma only
# 0 seconds -> OSD off
# 1 second -> show "Can't decode" messages only
OSD_TIMEOUT = 0
# Recent Enigma versions come with a new option "Use http authentication"
# in the Expert Setup menu. If this option is enabled, the Enigma web server
# requires all clients to authorize themselves with username (root) and
# password (usually dbox2 or dreambox). The following option tells newcamd
# about the authentication username and password to use for the web server
# in order to be able to display its on screen information.
OSD_WEB_LOGIN = root:dbox
#
# newcamd debug options
#
# dumps all ca systems used by a channel on the console
SHOW_ALL_CA_SYSTEMS = no
# print debug messages about ECM handling
DEBUG_ECM = yes
# print debug messages about EMM handling
DEBUG_EMM = yes
# print debug messages about Control Word Server (CWS)
DEBUG_CWS = yes
# print debug messages about dbox2 CAM (cam-alpha.bin)
DEBUG_CAM = yes
# hex dump of entire PAT
SHOW_PAT = no
# hex dump of entire PMT
SHOW_PMT = no
# hex dump of entire ECM
SHOW_ECM = no
# hex dump of entire CAT
SHOW_CAT = no
# hex dump of entire EMM (AU)
SHOW_EMM = no
# show network ECM messages being sent and received from/to the cardservers
SHOW_CWS_ECM = no
# show network EMM messages being sent and received from/to the cardservers
SHOW_CWS_EMM = no
# hex dump of EMMs with wrong signature
EMM_REPORT_WRONG_SIG = no
#
# newcamd optional settings
#
# Delay between reception of new control word and writing them into
# the CSA registers
# this is a default, can be changed for each individual key in keylist
DEFAULT_CW_DELAY = 0
# reload config on every channel zap
RELOAD_CONFIG_ON_ZAP = yes
# reload keylist on every channel zap
RELOAD_KEYLIST_ON_ZAP = no
# write osd ca info to file
CA_INFO_FILE = /tmp/cainfo.txt
#
# newcamd mandatory settings for control word servers (cws)
#
# Cardserver list
#
# <hostname> <port> <username> <password> <14 byte triple-des key in hex> <lan/wan> <cardserver name> [noecm]
#
# wan connections will be dropped and rebuild if newcamd is told so by camdcmd
# (see admin options)
#
# If the last word in the CWS line is noecm, newcamd will not attempt to send
# any ecms to that card, it will only send EMMs (AU) if userid is 1. Useful if
# you want to merge several cards of one provider into one port using
# cardspider.
#
# hostname = uds to use betad, port is the serial port in that case
#
# CWS = uds 1 dummy dummy
# CWS = linux.domain.com 10000 dummy2 dummy2 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserv
# CWS = 127.0.0.1 10000 dummy3 dummy3 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserv
#CWS = uds 0 local local
CWS = 192.168.178.100 15000 HD-Kathi0 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15001 HD-Kathi1 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15002 HD-Kathi2 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15003 HD-Kathi3 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15004 HD-Kathi4 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
#
# newcamd optional settings for using control word servers (cws)
#
# Timeout for cardserver login in 100ms
CWS_CONNECT_TIMEOUT = 20
# Port to listen for incoming cardserver connections (reverse login)
# and/or admin connections
CWS_INCOMING_PORT = 21000
# Port to get a list of all connected cardservers, just telnet to it
CWS_DEBUG_PORT = 12001
# send keep alive messages to servers to keep connections from dying by
# unreasonable router NAT timeouts, make sure all cardservers/spiders you
# conntect to are v5.25 or newer, otherwise you'll loose connection to them,
# if set to yes
# seems this feature is commonly misunderstood, it only keeps connections
# open even if no data packets are using it for while (NAT routers tend to
# forget about established tcp connections when they are inactive), it is
# NOT to automatically reconnect to servers, see also Q&A in readme.txt
CWS_KEEPALIVE = yes
#
# newcamd admin control options
# (incoming port is the same as CWS_INCOMING_PORT)
#
# <password> <14 byte des key>
#
ADMIN_PASSWORD = 0102030405060708091011121314
So, das war´s soweit für die Kathi!
Nun muss man noch die oscam in seinem Server kofigurieren.
6. Die datei oscam.conf sieht so aus:
7. So die oscam.user:[global]
Nice = -1
ClientTimeout = 5
CacheDelay = 120
Level = 15
BindWait = 10
LogFile = /dev/null
[monitor]
Port = 988
NoCrypt = 127.1.1.1
NoCrypt = 10.0.0.0-10.255.255.255
NoCrypt = 172.16.0.0-172.31.255.255
NoCrypt = 192.168.0.0-192.168.255.255
AULow = 120
MonLevel = 4
[newcamd]
Key = 0102030405060708091011121314
Port = 15000@1830:000000
Port = 15001@1702:000000
Port = 15002@0D05:000004
Port = 15003@1833:000000
Port = 15004@0500:023800,042200,023B00,024400
# -- camd 3.5x ----------------------------------------------------------------
# Port : Port-Number (0 disables this protocol)
# ServerIP : bind service to ONE dedicated ip-address
# -----------------------------------------------------------------------------
[cs378x]
Port = 54343
[cs357x]
Port = 20197
8. Nun noch die oscam aufm Server neu starten, und auf der Kathi unter "blaue Taste" das mgcamd.[account]
User = HD-Kathi0
Pwd = UFS-910
CAID = 1830
Group = 3
MonLevel = 4
Uniq = 1
[account]
User = HD-Kathi1
Pwd = UFS-910
CAID = 1702
Group = 1,3
MonLevel = 4
Uniq = 1
[account]
User = HD-Kathi2
Pwd = UFS-910
CAID = 0D05
AU = mastercrd
Group = 4
MonLevel = 4
Uniq = 1
[account]
User = HD-Kathi3
Pwd = UFS-910
CAID = 1833
Group = 3
MonLevel = 4
Uniq = 1
[account]
User = HD-Kathi4
Pwd = UFS-910
CAID = 0500
Group = 3
MonLevel = 4
Uniq = 1
Dann sollte es hell werden.
Wer mir jetzt noch sagen kann, wo mein Fehler liegt, warum bei mir nur die 1702 hell wird, der bekommt 100 Punkte!!!
P.S. Die "Group" in der oscam.user muss jeder für sich separat anpassen! Bei mir kommen manche CAID´s von ein und demselben Server, deshalb die doppelten Einträge.
Hoffe ich konnte so manchen hier helfen, die sich auch das mgcamd manuell einpflanzen müssen!