Habe ein Problem und zwar habe ich eine Kathrein vom Kollege bekommen,weil sie nach den flashen nur noch ufs910 anzeigte. Habe es mit kcc experten versucht und da zeigte er mir schon immer ip ping fehler an.Dann habe ich über Hypert. mit emergency.ub es glaube ich wieder hinbekommen.Dann notfall1.03 dann notfall1.06 dann 1.06 mit 2 bootl. klappt soweit alles.
Aber ich bekomme über der Netzwerkarte keine verbindung mehr hin woran könnte es liegen.
pll0 freq 531
pll1 freq 399
Net: VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
board_version = 0
Button_value = 6
Boot From Emergency Root File System Upate Appliction
Hit any key to stop autoboot: 0
## Booting image at a0040000 ...
Bad Magic Number
STB7100-REF>
Board: STb7100-mboard
U-Boot 1.1.2 (STLINUX_2_0p1) (Feb 23 2008 - 17:07:31)
DRAM: 32 MB
write time out = 1, clock = 40
write time out = 1, clock = 40
Flash: 16 MB
In: serial
Out: serial
Err: serial
pll0 freq 531
pll1 freq 399
Net: VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
board_version = 0
Button_value = 6
Boot From Emergency Root File System Upate Appliction
Hit any key to stop autoboot: 4
Board: STb7100-mboard
U-Boot 1.1.2 (STLINUX_2_0p1) (Feb 23 2008 - 17:07:31)
DRAM: 32 MB
write time out = 1, clock = 40
write time out = 1, clock = 40
Flash: 16 MB
In: serial
Out: serial
Err: serial
pll0 freq 531
pll1 freq 399
Net: VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
board_version = 0
Button_value = 7
Hit any key to stop autoboot: 0
STB7100-REF> print
boot_param_version=11
board=stb7100ref_27
bootdelay=10
°}W)ÜgÑ{ÜgÑ{Â
V)˜¶V)
autoload=n
bootargs=console=ttyAS0,115200 root=/dev/mtdblock3 mem=36m bigphysarea=1280
oprocessor_mem=2m@0x04000000,2m@0x04200000
bootcmd=bootm a0040000
stdin=serial
stdout=serial
stderr=serial
Environment size: 271/65532 bytes
STB7100-REF>
Board: STb7100-mboard
U-Boot 1.1.2 (STLINUX_2_0p1) (Feb 23 2008 - 17:07:31)
DRAM: 32 MB
write time out = 1, clock = 40
write time out = 1, clock = 40
Flash: 16 MB
In: serial
Out: serial
Err: serial
pll0 freq 531
pll1 freq 399
Net: VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
board_version = 0
Button_value = 7
Hit any key to stop autoboot: 0
STB7100-REF> printenv
boot_param_version=11
board=stb7100ref_27
bootdelay=10
°}W)ÜgÑ{ÜgÑ{Â
V)˜¶V)
autoload=n
bootargs=console=ttyAS0,115200 root=/dev/mtdblock3 mem=36m bigphysarea=1280
oprocessor_mem=2m@0x04000000,2m@0x04200000
bootcmd=bootm a0040000
stdin=serial
stdout=serial
stderr=serial
Environment size: 271/65532 bytes
STB7100-REF> setenv bootcmd bootm a0040000
STB7100-REF> setenv bootargs "console=ttyAS0,115200 root=/dev/mtdblock3 mem=32m
bigphysarea=1024 coprocessor_mem=2m@0x04000000,2m@0x04200000"
STB7100-REF> "saveenv"
Saving Environment to Flash...
env buffer crc = 9f9cfd37, data = 85e0000c
..
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash... .done
..
Protected 2 sectors
STB7100-REF>
Board: STb7100-mboard
U-Boot 1.1.2 (STLINUX_2_0p1) (Feb 23 2008 - 17:07:31)
DRAM: 32 MB
write time out = 1, clock = 40
write time out = 1, clock = 40
Flash: 16 MB
In: serial
Out: serial
Err: serial
pll0 freq 531
pll1 freq 399
Net: VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
board_version = 0
Button_value = 6
Boot From Emergency Root File System Upate Appliction
Hit any key to stop autoboot: 0
## Booting image at a0040000 ...
Bad Magic Number
STB7100-REF>
Board: STb7100-mboard
U-Boot 1.1.2 (STLINUX_2_0p1) (Feb 23 2008 - 17:07:31)
DRAM: 32 MB
write time out = 1, clock = 40
write time out = 1, clock = 40
Flash: 16 MB
In: serial
Out: serial
Err: serial
pll0 freq 531
pll1 freq 399
Net: VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
board_version = 0
Button_value = 7
Hit any key to stop autoboot: 0
## Booting image at a0040000 ...
Image Name: Linux-2.6.17.14_stm22_0037
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1697141 Bytes = 1.6 MB
Load Address: 84401000
Entry Point: 84402000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel console=ttyAS0,115200 root=/dev/mtdblock3 mem=36m bigphysarea=12
80 coprocessor_mem=2m@0x04000000,2m@0x04200000 - 0x00000000 - 0 ...
Linux version 2.6.17.14_stm22_0037 (root@develgod) (gcc-Version 4.1.1
ectronics/Linux Base 4.1.1-23)) #127 PREEMPT Tue Jul 1 19:41:06 CEST 2008
STMicroelectronics STb7100 Reference board initialisation
STb7100 version 3.x
Built 1 zonelists
Kernel command line: console=ttyAS0,115200 root=/dev/mtdblock3 mem=36m bigphysar
ea=1280 coprocessor_mem=2m@0x04000000,2m@0x04200000
st-coprocessor: Failed to reserve memory at 0x04000000
st-coprocessor: Failed to reserve memory at 0x04200000
PID hash table entries: 256 (order: 8, 1024 bytes)
Using tmu for system timer
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 27952k/36864k available (2821k kernel code, 8892k reserved, 360k data, 8
8k init)
PVR=04061100 CVR=30480000 PRR=00009100
I-cache : n_ways=2 n_sets=256 way_incr=8192
I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Mount-cache hash table entries: 512
CPU: STb
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
bigphysarea: Allocated 1280 pages at 0x847a3000.
JFFS2 version 2.2. (NAND) (C) 2001-2003
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Device probe found data for platform device lirc
lirc_dev: IR Remote Control driver registered, at major 61
lirc_dev: lirc_register_plugin: sample_rate: 0
lirc_dev: lirc_register_plugin: plugin lirc_stm owner 00000000
STM LIRC plugin has IRQ 125
Lirc STM: Using IRB mode
STMicroelectronics LIRC driver configured
STPIO layer initialised
VFD_Controller Type : NEW Kathrein VFD
STMicroelectronics ASC driver initialized
ttyAS0 at MMIO 0xb8032000 (irq = 121) is a asc
ttyAS1 at MMIO 0xb8033000 (irq = 120) is a asc
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
s_env_mac[0] =
s_env_mac[1] = s_env_mac[2] = s_env_mac[3] = s_env_mac[4] = ÿ
s_env_mac[5] = ÿ
s_env_mac[6] = ÿ
s_env_mac[7] = ÿ
s_env_mac[8] = ÿ
s_env_mac[9] = ÿ
s_env_mac[10] = ÿ
s_env_mac[11] = ÿ
s_env_mac[12] =
s_env_mac[13] = s_env_mac[14] = s_env_mac[15] = s_env_mac[
get ether addr = 0, 0, 0, 0, 0, 0
mac hi address = 0, lowaddress = 0
nwhw_config: device not found
ata1: SATA max UDMA/133 cmd 0xB9209000 ctl 0xB9209820 bmdma 0x0 irq 170
ata1: SATA link down (SStatus 0)
scsi0 : sata_stm
Generic ST boards onboard flash device: 0x01000000 (16.0Mb) at 0x00000000
Onboard_Flash: Found 1 x16 devices at 0x0 in 16-bit bank
Onboard_Flash: Found 1 x16 devices at 0x800000 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Onboard_Flash: CFI does not contain boot bank location. Ass
number of CFI chips: 2
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 10 MTD partitions on "Onboard_Flash":
0x00000000-0x00020000 : "1st stage BL: 0xA000.0000-0xA001.FFFF"
0x00040000-0x00200000 : "Kernel: 0xA004.0000-0xA01F.FFFF"
0x00200000-0x002a0000 : "Config FS: 0xA020.0000-0xA029.FFFF"
0x002a0000-0x004e0000 : "Root FS: 0xA02A.0000-0xA04D.FFFF"
0x004e0000-0x00ae0000 : "Application FS: 0xA04E.0000-0xA0AD.FFFF"
0x00ae0000-0x00c00000 : "Emergency FS:
0x00c00000-0x00fc0000 : "Data FS: 0xA0C0.0000-0xA0FB.FFFF"
0x00020000-0x00040000 : "BL1 Config: 0xA002.0000-0xA003.FFFF"
0x00fc0000-0x00fd0000 : "BL2 Config: 0xA0FC.0000-0xA0FC.FFFF"
0x00fd0000-0x01000000 : "2nd stage BL: 0xA0FD.0000-0xA0FF.FFFF"
ST40_start_host_control
ST40_start_host_control proceeding
ST40-ehci ST40-ehci.2: ST EHCI Host Controller
ST40-ehci ST40-ehci.2: new USB bus registered, assigned bus number 1
ST40-ehci ST40-ehci.2: irq 169, io mem 0xb91ffe00
ST40-ehci ST40-ehci.2: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: ST EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17.14_stm22_0037 ehci_hcd
usb usb1: SerialNumber: STB7100_EHCI
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver libusual
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegas
usb 1-1: new high speed USB device using ST40-ehci and address 2
usb 1-1: Product: USB2.0 Hub
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new driver pegasus
usbcore: registered new driver asix
usbcore: registered new driver cdc_ether
usbcore: registered new driver net1080
usbcore: registered new driver zaurus
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
stssc layer initialized
STMicroelectronics - Coprocessors st
st231-0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa4000000 size 0x00200000
cop. addr 0x04000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231-1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa4200000 size 0x00200000
cop. addr 0x04200000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
TCP bic registered
TCP highspeed registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 88k freed
/etc/init.d/rcS running...
Remounting root file system in read-write mode...mount: Can't find / in /etc/fst
ab
: Success
mount: Mounting / on (null) failed: Success
[FAILED]
/etc/rcS.d/S200mountfs: /etc/rcS.d/S200mountfs: 91: cannot create /etc/mtab: Rea
d-only file system
mount: Can't find / in /etc/fstab
: Success
mount: Mounting / on (null) failed: Success
Mounting other file systems...[ OK ]
Bringing up the loopback interface...[ OK ]
Setting up hostname...(none)
[ OK ]
BusyBox v1.1.0 (2006.03.02-09:48+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
config/start.sh does not exist.... running /app/start.sh
PARAM : boot_param_version=11
PARAM : board=stb7100ref_27
PARAM : bootcmd=bootm a0040000
PARAM : bootdelay=10
PARAM : °}W)Ü7Ï
V)˜¶V)d
U-
PARAM : bootargs=console=ttyAS0,115200 root=/dev/mtdblock3 mem=36m bigphysarea=1
DRAM: 32 MB
write time out = 1, clock = 4
280 coprocessor_mem=2m@0x04000000,2m@0x04200000 = 1, clock = 40
PARAM : stdin=serial
In: serial
PARAM : stdout=serialial
Err:
PARAM : stderr=serial
pll0 freq 531
PARAM : autoload=n9
Net
BOOT PARAM VERSION = 11
VFD_C
mknod: /dev/vfd: File exists VFD
vfd_driver_new: module license 'Marusys' taints kernel._value = 7
Hit any key to stop autoboot
tmp_pin = 8474d548
VFD_Driver Init at a0040000 ..
VFD_Controller Type : NEW Kathrein VFDagic Number
STB7100-RE
VFD_Driver Init
Board: STb7100
VFD PIO Already Opened
U-Boot 1.1.2 (
VFD PIO Already Opened2008 - 17:07:31)
VFD PIO Already Opened
.
Reading...
Erased
okec
Preproc Clock: Cut 3.0 detected -> setting Preproc clock.
..
Protected 2 sectors
stpio_core_init_module(): Initializing STPIO Module
U-Boot 1.1.2 (STLINUX_2_0p1)
Load module fdma [254] by insmod (pid 116)
DRAM:
STFDMA_ClbckMgr: task created ... Priority=99= 40
write ti
Load module stpti4_core by insmod (pid 118)
Flash: 16 MB
In: s
Load module stclkrv_core by insmod (pid 119)
Err: serial
pll0 freq 531
hdmi_i2c_init : Initializing I2CHDMI kernel Moduleer Init
VFD_Controller Type :
the adapter name is i2c-ssc-0 number 0
board_version = 0
the adapter name is i2c-ssc-1
pll0 freq 531
LX loaded:ll1 freq 3
Base: 0xa4200000: VFD_Driver Ini
Last: 0xa4347284
VFD_Controlle
Size:1340036threin VFD
mod_lxload_exit: Exiting LXLOAD kernel Moduleon = 0
Button_value = 6
The I/O memory region 0x04200000 is released successfullyliction
Unload module lxload by rmmod (pid 141)
## Booting
mod_lxload_init: Initializing LXLOAD kernel Module, StartAddress: 0x04000000
STB7100-REF>
Board: STb7100-mboard
Load module lxload[253] by insmod (pid 142)08 - 17:07:31)
LXLOADER virtual io kernel address of phys 0xa400
write time out = 1, clo
board_version = 0
LX loaded:alue = 6
Base: 0xa4000000 From Emergency Ro
Last: 0xa403403ce Appliction
Size:213052
mod_lxload_exit: Exiting LXLOAD kernel Moduleoot: 0
## Bo
The I/O memory region 0x04000000 is released successfully
Bad Magic Number
STB7100-REF>
Unload module lxload by rmmod (pid 152)
U-Boot 1.1.2 (STLINUX_2_0p1) (
EMBXSHM-PortClosed: with RT priority done with syscall. PID=159
DRAM: 32 MB
write time out = 1, clo
EMBX EMBXSHM-PortClosed: task created ...ite time out = 1, clock = 40
stblit_ioctl_init_module: Initializing STBLIT IOCTL Module NEW Kathrein VFD
bo
Load module stblit_ioctl[248] by insmod (pid 196)
Hit any key to stop autoboot: 0
mknod -m 0660 /dev/stapi/stblit_ioctl c 248 0ge at a0040000 ...
stlayer_ioctl_init_module: Initializing STLAYER kernel Module
Board: STb7100-mboard
U-Boot 1.1.2
Load module stlayer_ioctl[247] by insmod (pid 204)
DRAM:
mknod -m 0660 /dev/stapi/stlayer_ioctl c 247 0 40
write time
Load module stpti4_ioctl [246] by insmod (pid 212)
Flash: 16 MB
In: serial
mknod -m 0660 /dev/stapi/stpti4_ioctl c 246 0
pll0 freq 531
pll1 fr
Load module stclkrv_ioctl [245] by insmod (pid 220)
VFD_Controller Type : NEW Ka
DR
mknod -m 0660 /dev/stapi/stvmix_ioctl c 241 0ock = 40
writ
stvbi_ioctl_init_module: Initializing STVBI kernel ModuleFlash: 16 MB
In: serial
Out:
Load module stvbi_ioctl[240] by insmod (pid 260)pll0 freq 531
pll1 freq 399
mknod -m 0660 /dev/stapi/stvbi_ioctl c 240 0
VFD_Controller Type : NEW Kathrein VFD
Load module stmerge_ioctl [239] by insmod (pid 268) = 0
Button_value = 7
mknod -m 0660 /dev/stapi/stmerge_ioctl c 239 0
STB7100-REF> setenv boot
Load module staudlx_ioctl[238] by insmod (pid 276)=36m
mknod -m 0660 /dev/stapi/staudlx_ioctl c 238 0280
> oprocessor_mem=2m@0x0400
LMI_SYS SCR = 00000000
stderr=serial
LMI_SYS STR = 35b06455le=ttyAS0,115200 root=
LMI_SYS COC = 00000000bigphysarea=1280
LMI_SYS SDRA0 = 08001900
LMI_SYS SDRA1 = 08001900cessor_mem=2m@0x04000000
LMI_SYS CIC = 00000249
LMI_SYS SDMR0 = 00000000 a0040000
LMI_SYS SDMR1 = 000000001.64
LMI_VID MIM0 = 057c025f
LMI_VID MIM1 = 00000005
LMI_VID SCR = 00000000
LMI_VID STR = 35b06455
LMI_VID COC = 00000000
LMI_VID SDRA0 = 14001900
LMI_VID SDRA1 = 14001900
LMI_VID CIC = 00000249
LMI_VID SDMR0 = 00000000
LMI_VID SDMR1 = 00000000
UFS910 Button Device Driver(by Marusys Co.)
TestModMgr::CheckTestMode CmdLine = console=ttyAS0,115200 root=/dev/mtdblock3 me
m=36m bigphysarea=1280 coprocessor_mem=2m@0x04000000,2m@0x04200000
CMDLINE = console=ttyAS0,115200 root=/dev/mtdblock3 mem=36m bigphysarea=1280 cop
rocessor_mem=2m@0x04000000,2m@0x04200000
CMDLINE = console=ttyAS0,115200 root=/dev/mtdblock3 mem=36m bigphysarea=1280 cop
rocessor_mem=2m@0x04000000,2m@0x04200000
cannot fine test mode
TestModeMgr::CheckMode : TestMode Disabled
