NEU !
Hat das schon jemand drauf und/oder kann berichten ?
NEU !
Hat das schon jemand drauf und/oder kann berichten ?
.
.
.
Gruß NOLLE
. .
objektiv betrachtet, ist alles subjektiv
Ist schon Geil, ich dachte auch ich sehe nicht richtig.
Hier das Release
http://www.****upload.com/?d=Z6G2KCUI
The provided image is based on the Linux operating system and includes
the Enigma2 PVR application. Please read this document carefully before
installing the image.
Unsupported features and known problems
---------------------------------------
- CAM slots are not supported yet.
- The only supported tuner type is DVB-S2 CX24116/CX24118.
- Timeshift does not work yet.
- Rewind does not work properly. Sometimes enigma2 freezes when rewinding.
"Jump back" can be used instead (see playback keys).
- Samsung LCD TVs will probably have problems with the default resolution
576i.
- There might be no video on the FIRST (!) start after installation - reboot
the box.
DISCLAIMER
----------
The software is provided 'as is' without warranty of any kind.
Please consider that you may lose manufacturer's warranty when installing
this image.
This is an alpha image. That is some functions may not be available or be
buggy (causing crashes/freezes or loss of data).
The installation of the Enigma2 image formats (ext2) the internal harddrive.
ALL FILES ON THE HARDDRIVE WILL BE LOST.
Installation instructions
-------------------------
You will need either a USB stick or a USB harddrive with FAT32 filesystem.
- Copy the files Enigma_Installer.tfd, uImage and rootfs.tar.gz to the USB
device.
- Attach the drive to the USB slot.
- Open the Topfield firmware update menu and select the image file
Enigma_Installer.tfd on the USB drive.
- Start the firmware update from USB.
- After about 6-7 minutes the installation should be finished.
DO NOT REMOVE THE USB DEVICE UNTIL the INSTALLATION HAS FINISHED.
During the installation the VFD shows the current installation step and
error messages (if any):
"9 USB STCK" mouting USB stick
"8 HDD PART" partitioning HDD
"7 HDD FMT" formatting HDD (root fs)
"6 HDD FMT" formatting HDD (data fs)
"5 HDD SWAP" creating swap
"4 ROOT FS" installing root file system
"3 LOADER" flashing U-Boot settings
"2 KERNEL" flashing kernel
"1 FSCK" checking file system
"0 REBOOT" rebooting within 2 seconds
It is recommended to attach a cable to the serial port and log the output in a
terminal program (e.g. TeraTerm) during the installation and the first start.
The USB filesystem should be writable to prevent infinite installation loop.
(The file uImage is renamed to avoid the infinite loop.)
The first start usually takes approximately 3 minutes due to creation of
device nodes.
Enigma2 can be removed by flashing a regular Topfield firmware image using
standard tools like TFD-Down or VegaPack.
First start
-----------
On the first start the Enigma2 interactively configures the video output to be
used. The following options are available:
- Component
- HDMI
- Scart
- HDMI-PC
Each connection type is switched on for 30 seconds. The VFD displays the
connection type which is currently active. You can either wait until the
connection type you want is displayed and your TV shows a picture or you
can select the connection type with Up and Down buttons on the remote control.
Confirm the desired connection type with the Ok button. After that you can
proceed with the configuration supported by the configuration wizard.
The image contains a default channel table. If you want to replace it You can
perform a channel scan later.
Network configuration
---------------------
The U-Boot settings contain the following configuration by default:
MAC address 00:3e:9e22:33
IP address 192.168.178.100
That is after booting the image you can login via telnet if your computer is in
the same subnet.
These values are set up by the U-Boot. You can temporarily change the values
in Enigma2 menu "Settings/System/Network.../Adapter settings" or change the
U-Boot parameters.
Default U-Boot bootargs:
ba1=console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:192.168.178.10:192.168.178.10:2 55.255.255.0:tf7700:eth0:off nwhwconf=device:eth0,hwaddr:00:3e:9e22:33
mem=128m bigphysarea=4000 coprocessor_mem=4m@0x10000000,4m@0x10400000
To change the IP addresses interrupt the U-Boot countdown and execute the
following command with replaced IP addresses:
TF7700> set ba1 'console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=<own IP>:<server IP>:<DNS IP>:255.255.255.0:tf7700:eth0:off nwhwconf=device:eth0,hwaddr:00:3e:9e22:33
mem=128m bigphysarea=4000 coprocessor_mem=4m@0x10000000,4m@0x10400000'
Please note that the setting has to be split in two lines to bypass the
limitation of U-Boot. The second line must start with a white space. The
string is enclosed in single quotes. Any change is temporary unless the
settings are saved to flash using the command "saveenv". Before saving
settings to flash you should test whether the kernel boots with your settings.
Enter "boot" at the U-Boot prompt to start the kernel. (After testing the
settings without saving them you will have to enter your changes again.)
Playback keys
-------------
Play - shows the file list
Yellow - pause/unpause playback
Green - continue playback
Red - jump to the beginning
Blue - jump to the next bookmark
1/3 jump 15 seconds backwards/forwads (configurable in the settings menu)
4/6 jump 60 seconds backwards/forwads (configurable in the settings menu)
7/9 jump 5 minutes backwards/forwads (configurable in the settings menu)
Full key map can be found in the file /usr/local/share/enigma2/keymap.xml.
Team Ducktales
Arcon_Titan_2010
Arcon_Titan_4000
Icecrypt S4000
Octagon 1018
Astro ASR 1200
Rebox HD8000
Rebox HD4000
SkyStar HDS2
Dream 7000
MfG Klick
hdfreaks.cc
arcon-friends.net
Hallo...
hier gibt es doch einige TF 7700HDPVR Besitzer !
Hat es noch keiner getestet ?
Ich hab mir die firm unterdessen besorgt, aber noch nicht installiert.....
Nicht weil ich feige bin... nein, weil die HD mit ext2 neu formatiert wird... und da sind noch 600GB HD Filme drauf....
.
.
.
Gruß NOLLE
. .
objektiv betrachtet, ist alles subjektiv
Naja, auf was wartet ihr? Das ein EMU läuft, das wird sicher bald funzen. Wenn es nicht schon funzt.
So hast du bestimmt schon gelesen das erstmal nur ein Tuner unterstützt wird. Der Rest wäre mir egal.
E2 ist auf der Box der Hammer. (Sagte mir mein Kumpel)
Arcon_Titan_2010
Arcon_Titan_4000
Icecrypt S4000
Octagon 1018
Astro ASR 1200
Rebox HD8000
Rebox HD4000
SkyStar HDS2
Dream 7000
MfG Klick
hdfreaks.cc
arcon-friends.net
Hallo ich habe es drauf.
zuerst sollte man wissen das das Image auf die HDD kommt und somit die ganze Platte neu formatiert wird. Es werden dann 3 Partitionen erstellt.
SDA1 für das system, sda2 für swap und sda3 für Movies.
Im flash kommt ein Boot Eintrag rein um von platte zu starten.
Man kann mit Topset 2.0 und RS232 und Nullmodem kabel das original Image wieder flashen um den boot dings wieder wegmachen.
Enigma2 hat noch bisschen Stabilität Probleme auf den Topfield
2 gleichzeitige Aufnahmen funzen nicht richtig, nur die erste läuft durch. Bei der 2ten Aufnahme wird zwar eine info abgelegt aber der inhalt ist leer.
Man kann eine Aufnahme machen(freeTV) und sonst frei zappen.
wie schon in der readme steht funzt kein timeshift und kein cam Modul.
Ansonsten funzt die Lan Schnittstelle. HD Sender laufen soweit auch ohne Probleme.
Mit der Kanalsuche habe ich so meine Probleme und werden nicht alle Sender gefunden.
Aber es gibt ja genügend fertige enigma2 Settings die man verwenden kann.
Frage zu emu.
ja gibt es habe da einiges ausprobiert.
Der Topfield hat einen STI chipsatz und alles was auf STI_linux läuft geht auch mit der Box. Da muss man mal ein blick in den UFS910 bereich reinschauen. Nur ist die Datenstruktur nicht identisch des UFS 910. Ich musste die Camd3 und alle andere Dateien in eine, Ordner /var/bin einfügen und aus dem Verzeichnis starten. Da ich wenig erfahrung habe würde ich gerne das optimieren und einen Autostart des Emu machen. Brächte da Hilfe wie man das macht.
Leider habe ich kein twin support mit dem Emu. Cardsharing sollte auch funzen.
Wie gesagt dieses Image ist die erste veröffentlichte Beta für den 7700HDPVR.
Wer eine zuverlässige box haben will sollte vielleicht noch etwas warten.
Aber wer mal mit testen und rumspielen will kann da gerne zugreifen.
MFG
Geändert von PeterPan4711 (26.03.09 um 21:40 Uhr)
so langsam wirds mit unserem Topf....
################################################## #######
# #
# Team Ducktales' Enigma2 image for the TF7700HDPVR #
# #
# Release 0.2 #
# #
################################################## #######
The provided image is based on the Linux operating system and includes
the Enigma2 PVR application. Please read this document carefully before
installing the image.
New features and bugfixes (since 0.1)
-------------------------------------
+ Feature: first beta support for CAMs (upper slot only)
+ Feature: added flashing topfield.tfd (if present on the USB stick) to
make going back to Topfield firmware easier
+ Feature: freed 16 MB of unused RAM
+ Feature: migrated system partition to ext3 filesystem
+ Feature: migrated to stlinux-2.6.17.14-0041
+ Feature: installation control file (noformat, noupdate, nopartition,
keepsettings, usbhdd)
+ Feature: enabled installation to a USB HDD (option usbhdd)
+ Feature: improved emergency shutdown policy
+ Change: removed mapping of the keys V- (left) and V+ (right) to volume control
to avoid problems in various menus. The volume can now be adjusted with
the keys |< and >|.
+ Fix: the keys V-/V+ can now be used to change entries in the timer menu and
to scroll page up/page down.
+ Fix: updated the settings for Astra 19°° and added new satellites.xml for
orbital position 13.0, 19.2 and 23.5 east
+ Fix: applied the SATA patch to fix interactions with HDDs
+ Fix: fixed repeating Diseq commands delaying tuning up to 20 seconds
+ Fix: added swap to /etc/fstab
+ Fix: added the dvr1 device for recording
+ Fix: added updating the network settings to the rcS (activates the user
settings made in e2)
+ Fix: fixed the issue with "SID not found in PAT" and some scan problems
+ Fix: fixed the issue with low volume
+ Fix: improved shutdown behavior so that the PVR is not turned off before
the kernel finished unmounting file systems
+ Fix: updated Vader skin (DNS settings, timer)
+ Fix: swapped keys zapUp and zapDown
+ Fix: Daylight Saving Time
- Fix: no video on the FIRST start after installation
Unsupported features and known problems
---------------------------------------
- The only supported tuner type is DVB-S2 CX24116/CX24118.
- Timeshift does not work yet.
- Rewind does not work properly. Sometimes enigma2 freezes when rewinding.
"Jump back" can be used instead (see playback keys).
- Samsung LCD TVs will probably have problems with the default resolution
576i.
- HDD shuts down and spins up very often, workaround - disable HDD standby in
e2 settings.
- With "AC3 downmix on" there is no sound on optical when AC3 stream is
selected. With "AC3 downmix off" the system migt freeze when zapping to
channels with AC3.
- After stopping the playback of a an active recording (a kind of timeshift)
the screen remains black and does not recover until the receiver is restarted.
.
.
.
Gruß NOLLE
. .
objektiv betrachtet, ist alles subjektiv
jepp gibt sogar 0.2.1 Bugfix zu 0.2
+ Fix: updated satellites.xml in /etc/tuxbox
+ Fix: changed the shutdown procedure to prevent corrupting the filesystem
+ Fix: fixed minor issues with tuxtxt
+ Fix: fixed minor issues in CAM handling
+ Fix: fixed the issue with e2 settings not saved during an update or
reinstallation
Topfield 7700HDPVR mit Enigma2
Hat sich das noch jemand angetan das enigma2 ?
Topfield 7700HDPVR mit Enigma2
Warum ?
Topfield 7700HDPVR mit Enigma2