so einen editor hab ich benutzt nothing es kann nur an der kahti liegen noch ne idee ?
muss es mg_cfg oder mg.cfg heißen ?
so einen editor hab ich benutzt nothing es kann nur an der kahti liegen noch ne idee ?
muss es mg_cfg oder mg.cfg heißen ?
Hier kannst Du die Log Option einstellen:
L: { 04 } 192.168.1.23 8024 /tmp/mgcamd.log
Mach das mal und starte dann mgcamd neu. Dann schauen wir was in der Datei steht.
Die IP mußt Du anpaßen
MfG Tomyslav
DBox 1 DVB 2000
DBox 2 KW Image
Dreambox 800 NN²
Humax 5400Z TOH 11.3
Kathrein UFS 910 E²
Kein Support über PN!
__________________
ich weis nicht obs das ist aber aber
mgshare.info
newcamd route 0000:dummy1:192.168.178.140:34000:unknown EMM OFF offline
ist es das ?
mgstart.info
tuxbox mgcamd v1.31 by mixvt (compiled Oct 27 2008 23:09:59), Wed Mar 11 12:22:28 2009
mg uptime 00d 00h 02m 02s, service changes: 1, ecm processed: 0, lost cw warnings: 0
Newcamd:
Host/port Recon. Emm out Ecm out Cw in Avg. ecm time
192.168.178.140 :34000 0 0 0 0 0
Box: uptime = 170s, CPU load: 1 min 165792 / 5 min 73024 / 15 min 27424
RAM in bytes: total 30609408 / free 1396736 / shared 0 / buffers = 2011136
mgcamd: total memory allocated by malloc, in bytes: 135168 (132kb), chunks 9008
Nein das ist die Share info aber nicht der Log von mgcamd.
Hast Du eigentlich mal alles neu gestartet nach den Umstellungen auch die Serverbox?
MfG Tomyslav
DBox 1 DVB 2000
DBox 2 KW Image
Dreambox 800 NN²
Humax 5400Z TOH 11.3
Kathrein UFS 910 E²
Kein Support über PN!
__________________
jo alles neugestartet kathi dreambox emus newcs nothing
ich frag mich warum er die log nicht macht
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
U: { 05 }
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30
# network ecm timeout in seconds
K: { 05 }
# newcamd dead routes connect retry, sec
Q: { 600 }
# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
# Neutrino:
#O: { 01 } root dbox2
# Enigma:
#O: { 02 } root dbox2
# Dreambox:
#O: { 02 } root dreambox
# Kein OSD:
O: { 00 } root dbox2
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 15 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 00 } 192.168.178.100 8024 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 07 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 00 }
muss es mg_cfg oder mg.cfg heißen ?
mg_cfg paßt schon
Weil Du den Log noch ausgeschaltet hast. Muß so aussehen:
L: { 04 } 192.168.178.100 8024 /tmp/mgcamd.log
Die IP mußt Du noch anpaßen und evtl. den Pfad
MfG Tomyslav
DBox 1 DVB 2000
DBox 2 KW Image
Dreambox 800 NN²
Humax 5400Z TOH 11.3
Kathrein UFS 910 E²
Kein Support über PN!
__________________
tuxbox mgcamd v1.31 by mixvt (compiled Oct 27 2008 23:09:59)
[mg] Net7:0:5s Show ecm:1, emm:1 Up:5 Au:2 Dir:0 Osd:no:80:0 Cache:7 Log192.168.178.100:8024 Reread:7
[mg] Ecm cache time: 15
Box type: stapi
Conax.Key error 2: No such file or directory
SoftCam.Key error 2: No such file or directory
AutoRoll.Key error 2: No such file or directory
Conax.Key error 2: No such file or directory
[config] newcamd route = dummy1:192.168.178.140:34000 server cardserv
newcamd keep alive: 0, incoming port: 0
[mgcam] emm thread started
[mgcamd] tps update started.
/data/keys/tps.bin error 2: No such file or directory
[mg0] service 6DCA index 0 pmt pid 0 (1)
[newcamd] Connecting to 192.168.178.140:34000...
[newcamd] Login to 192.168.178.140:34000 as dummy1 failed (112ms)
[mg0] No supported encryption system found
[mg0] stopped
so das ist sie nun
OK
Kann dir aber leider nicht mehr weiterhelfen.
Da es am Login scheitert würde ich es nochmal mit einem anderen Benutzernamen und Kennwort versuchen. Vielleicht mal ohne Zahlen
MfG Tomyslav
DBox 1 DVB 2000
DBox 2 KW Image
Dreambox 800 NN²
Humax 5400Z TOH 11.3
Kathrein UFS 910 E²
Kein Support über PN!
__________________
ok werd ich nochmal versuchen wenn nicht brech ich in tärnen aus ^^
Das kannst Du auch noch ändern:
# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 02 }
MfG Tomyslav
DBox 1 DVB 2000
DBox 2 KW Image
Dreambox 800 NN²
Humax 5400Z TOH 11.3
Kathrein UFS 910 E²
Kein Support über PN!
__________________
in Post Nr. 6 hast du in deiner newcamd.list den User "kahti"
und in deiner newcs.xml "kathi"
GigaBlue Quad HD, Kathrein UFS-913, DBox2 Philips, LED TV Philips 7108,
Hotbird 13.0, Astra 19.0
wow danke du hast recht es verbindet nun immerhin zu newcs und die kathi kommt online in newcs menü leider ist noch alles dunkel
er fragt ok ECM ab und hat 10 abgefragt bleibt aber dunkel wie das ?
Geändert von jesus12 (11.03.09 um 16:34 Uhr)
diesen Thread habe ich nur überflogen, evtl. hilft dir dieser Thread noch weiter:
http://www.spinnes-board.de/vb/showthread.php?t=129730
GigaBlue Quad HD, Kathrein UFS-913, DBox2 Philips, LED TV Philips 7108,
Hotbird 13.0, Astra 19.0
ich hab alles so gemacht wies im thread steht :(
ICH DANKE ALLE DENEN DIE MIR GEHOLFEN HABEN ES LÄUFT wuhu
Schön das es läuft, es wäre noch gut zu wisen, woran es gelegen hat damit wir alles was davon haben.
GigaBlue Quad HD, Kathrein UFS-913, DBox2 Philips, LED TV Philips 7108,
Hotbird 13.0, Astra 19.0