Ja dann bleiben wir hier. Ich dachte nur weil Du eine DBox hast und das hier der Kathrein Bereich ist und auf der DBox gäbe es noch einfachere Wege zu CS als mit mbox und mpcs. Poste hier mal deine configs von mbox, mpcs und die cwshare.cfg
Ja dann bleiben wir hier. Ich dachte nur weil Du eine DBox hast und das hier der Kathrein Bereich ist und auf der DBox gäbe es noch einfachere Wege zu CS als mit mbox und mpcs. Poste hier mal deine configs von mbox, mpcs und die cwshare.cfg
MfG Tomyslav
DBox 1 DVB 2000
DBox 2 KW Image
Dreambox 800 NN²
Humax 5400Z TOH 11.3
Kathrein UFS 910 E²
Kein Support über PN!
__________________
hallo musicnapper,
vielen Dank mal für die Antwort, hab mir schon seit Tagen massiv den Kopf zerbrochen was ich falsch mach.Dann liegts also an der mbox.
Du sagtest:
nutze dazu die ver23-3 das ist die letzte die beides kann
Wo bekomm ich die denn her?Und wie installier ich die dann,ich vermute es sind drei dateien für meine Kathi?
mbox nach /var/emu, und cwshare.cfg und mbox.cfg nach /var/kes/ ? Übrigens benutze ich auf meiner Kathi Diablo cam modul das müßte doch damit gehen oder
viele Grüße nils
Geändert von nils22 (02.03.09 um 15:30 Uhr)
@nils22
Wo hast du denn die Zusammengewürfelte cwshare her?Hier die cwshare:
# allow maximum 06 share level for recieved card data
I: { 04 }
# 01 repeat EMM's
# 00 consider every EMM only once
# 01 restart pid on overflow
# 1* reset ENX on every channel change
# *1 check/reset ENX freezes on FTA
# *2 check/reset ENX freezes on *****
# *3 check/reset ENX freezes on FTA and *****
# 00 write nothing in atack.txt
# 01 write into atack.txt: password is wrong
# 02 write into atack.txt: ID unknown
# 04 write into atack.txt: IP is wrong
# 08 write into atack.txt: port is worng
# 10 write into atack.txt: share.stat
# 20 create online.log for online/offline logging
# 3F write everything. (combine bits for other combinations)
# 4000 send ecm again after 4 Seconds if no reply.
# 6000 resync decode after 6 Seconds if net decode failed
N: { 00 01 03 1F 3000 5000 }
# Send ECM's at maximum 5 cards (please use this as default)
X: { 05 }
# Send ECM's in any case to these card ID's, even they are more then X:
# some examples ...
#G: { 17020000 1235 }
O: { 2000 2000 }
# For W: please read the cwshare.txt, here only some examples
# use card 1 only for the following pids
#W: { 01 02 02 } 1022 100A 100B 102B 1009 101D 1029 1014 1011 101B
# don't use card 2 for the following pids
#W: { 02 03 03 } 1008 1016
# S: is the same as W:, just using the SID instead of the ECMPID
# cwshare.cfg --- ufs910 --- internet and local network
#
# password
M:{ beimirgehtnix.dns.com { 1156AACE }
# Internet Friends port range password cod
#D: { friend1.homeip.net { 8010 8010 { B142AB11 { 5 5 }}}}
#D: { friend2.homelinux.net { 8010 8010 { 81BFF901 { 5 5 }}}}
G: { beimirgehts.server.com { 2500 2500 { AB236690 { A3 A3 }}}}
{ 0000 } { 0 } send filter
{ 0000 } { 0 } receive filter
# other local boxes
#D: { 192.168.0.17 { 2499 2499 { 20000001 { 5 5 }}}}
#D: { 192.168.0.52 { 8020 8020 { BA334B24 { 5 5 }}}}
#D: { 192.168.1.11 { 2499 2499 { BA334B24 { 5 5 }}}}
Das ist eine cwshare von G..x bzw alte Mbox!
Die N: Line sowie W: Line muß raus! Ein S: leuchtet ja auch noch durch
Was soll das? Was soll nun genommen werden?
G: { 17020000 1235 }
G: { beimirgehts.server.com { 2500 2500 { AB236690 { A3 A3 }}}}
raus damit -> G: { 17020000 1235 }
Auskommentiert wird bei Mbox so "//" und nicht so "#"
3xD-Box1 DVB2K 2xD-Box2 Neutrino 1xUfs910
Ok, stelle gleich meine Config ein....
Habe schon Hoffnung.....
Dann fange ich mal an:
Ich habe das GLJ-Image aufgespielt und anschließend ein Online-Update gemacht.
Meiner DBox (Server)habe ich intern die IP-Adresse 192.168.1.5, meiner Kathi 192.168.1.6, meinem Rechner die 192.168.1.3 und dem Router 192.168.1.1 zugewiesen. Im Router leite ich den Port 10110 auf die 192.168.1.5 und die 10111 auf die 192.168.1.6
Anschließend habe ich online die MBox V0.4 build 0022 und MPCS 0.9c-gbx-beta5.3 heruntergeladen.
Nun habe ich in meiner Config folgende Einstellungen vorgenommen:
mpcs.conf:
[global]
Nice = -1
ClientTimeout = 5
ClientMaxIdle = 120
CacheDelay = 0
BindWait = 60
ResolveDelay = 30
LogFile = /dev/null
Sleep = 0
#ServerIP = 192.168.178.3
Locals = 17020000
IgnoreList = /var/keys/ignore.list
[monitor]
Port = 8000
NoCrypt = 127.1.1.1
NoCrypt = 10.0.0.0-10.255.255.255
NoCrypt = 172.16.0.0-172.31.255.255
NoCrypt = 192.168.0.0-192.168.255.255
AULow = 120
MonLevel = 4
[newcamd]
Port = 15000@1702:FFFFF;15001@1833:FFFFF
Key = 0102030405060708091011121314
mpcs.server:
[reader]
Label = multicam
Protocol = mouse
Device = /dev/tts/1
EMMCache = 1,3,2
Detect = DSR
CAID = 1702,1833
Group = 1
mpcs.user
[account]
User = dummy
Pwd = dummy
Group = 1
1801to1702 = 1
AU = multicam
MonLevel = 4
mbox.cfg (wegen der Übersicht habe ich alle Einträge, bei welchen
ein “//“ oder eine „#“ vorsteht weg gelassen. Ich hoffe man kann mit beiden
auskommentieren, sonst könnte hier auch ein Fehler liegen!?!?):
D: { 1 }
B: { 0 }
Z: { 11 } { 192.168.1.3 8080 }
U: { 1 }
L: { 1 }
F: { 500 }
T: { /tmp/ }
K: { /var/keys/ }
E: { 1 }
M: { 1 }
P: { /tmp/pmt.tmp }
W: { 0 }
H: { 0 }
Q: { 30 }
cwshare.cfg
I: { 02 }
X: { 05 }
M: { meine.dyndns.org { 12345678 }}
O: { 2000 2000 }
D: { kathi.dyndns.org { 10110 10110 { C8D8A6B9 { 1 1 }}}}
D: { dbox2.dyndns.org { 10110 10108 { B8C8D6A1 { 1 1 }}}}
D: { 192.168.1.6 { 10110 10111 { 12345672 { 1 1 }}}} # kathi lokal
C: { 127.0.0.1 15000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 } { 10 } { 1702FFFF:17020000 }
C: { 127.0.0.1 15001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 } { 10 } { 1833FFFF:18330000 }
Ich hoffe dass mir nun jemand helfen kann. Da ich wie erwähnt die Auskommentierugen weg gelassen habe hoffe ich nich, dass hier der Fehler liegt!
Tausend Dank vorab!!!
Geändert von Muster1234 (02.03.09 um 17:17 Uhr)
cwshare.cfg:@Tomyslav: Poste hier mal deine configs von mbox, mpcs und die cwshare.cfg
-------------
M: { 192.168.178.111 { FA1BC9F9 }}
O: { 2000 2000 }
D: { 192.168.178.222 { 8006 7005 { 12345678 { A3 A3 }}}}
C: { 127.0.0.1 15000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 } { 10 } { 1702FFFF:17020000 }
C: { 127.0.0.1 15001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 } { 10 } { 1833FFFF:18330000 }
#192.168.178.111: IP D-Box
#192.168.178.222: IP Kathi
mbox.cfg:
----------
//mbox.cfg EXPLANATION and EXAMPLES
D: { 1 }
//x=0 -> disable
//x=1 -> enable dbox2 cw writing
//x=2 -> enable STAPI for IPBOX
//x=3 -> enable STAPI for Kathrein
//default disabled
B: { 0 }
//B: { x }
//x=0 -> disable local UDP ports 8004-80xx ,this ports are used with DVB cards and gbox plugin (Windows and Linux)
//x=1 -> enable
//default disable
#Z: { 12 } { 127.0.0.1 8000 }
Z: { 11 } { 192.168.178.201 8080 }
// Z option -> control sending/writing current informations
// Z: { xy } { IP port }
// x=0 -> don't print time stamp (in console screen and in debug file)
// x=1 -> print time stamp ( .... )
// y=0 -> no writing/sending informations to debug file/destination IP
// y=1 -> send informations to destination IP but not in debug file
// y=2 -> write informations to debug file but don't send to destination IP
// y=3 -> write/send informations to debug file/destination IP
// IP port -> destination IP and UDP port where to send informations
// no default
#C: { 127.0.0.1 7999 }
// C option -> control receiving some command messages localy or from another IP
// C: { IP port }
// IP-> your local IP or you DNS
// port -> on what port you will be waiting command messages
// no default
U: { 1 }
// U options -> Update peer(s) IP if it changes while peer still resending ecm's/cw etc.. information
// default only on hello message peer(s) IP are updated !!!
// U: { x }
// x=0 -> disabled
// x=1 -> enabled
// default disabled
L: { 1 }
// L option -> how mbox to menage virtual card(s) with level 0
// ( only for peer(s) who have and can reshare virtual cards but don't want to use LEVEL 0 card(s) for them self)
// L: { x }
// x=0 -> don't load any virtual cards with LEVEL 0, you can't use them for your self
// x=1 -> load all virtual cards with LEVEL 0 ,you will be using them for your self
// default 1
F: { 500 }
//F option -> reset writing debug.txt from begining if file size is higher then (x)(KB)
//F { x } -> decimal in KBytes
//default 500 KB
#G: { /hdd/ }
//G option -> redirect writing ONLY debug.txt file to internal or external HDD in receivers or for any other reason.
//Remove #, ONLY if you want to use this option !!!!!!!
T: { /tmp/ }
// T option -> where to store temp files ... (share.info,debug.txt ,etc.)
// T: { folder_path_to_files, example: T: { /tmp/ } }
K: { /var/keys/ }
// K option -> where is cwshare.cfg file
// K: { folder_path_to_files, example: K: { /var/keys/ } }
E: { 1 }
// E option -> disable same cards from peers
// E: { x }
// x=0 -> use same cards(boxids) from peers
// x=1 -> don't use same cards(boxids) from peers
// default 1
M: { 1 }
// M option -> Mode option
// M: { x }
// x=0 -> local mode no NET
// x=1 -> NET mode
// default 0
P: { /tmp/pmt.tmp }
// P option -> PMT location (Dont used with linux and windows)
// you must be tuned to channel so image can generate this file
// { /tmp/pmt.tmp } for resivers and images that create this file <- use this if you can
// { 1/tmp/camd.socket } for enigma 1
// { 2/tmp/camd.socket } for enigma 2
W: { 0 }
// W option -> write raw ECM to ecm.raw file
// W: { x }
// x=0 -> disabled
// x=1 -> enabled
// default disabled
H: { 0 }
//H option -> C line priority over network cards
// H: { x }
// x=0 -> disabled -> newtwork cards has priority over your local cards
// x=1 -> enabled -> your local cards has priority over network cards
// default disabled
Q: { 30 }
//Q option -> newcamd connect retry in sec.
//Q: { x }
// default 300 sec.
mpsc.conf:
-----------
[global]
Nice = -1
ClientTimeout = 5
ClientMaxIdle = 120
CacheDelay = 0
BindWait = 60
ResolveDelay = 30
LogFile = /dev/null
Sleep = 0
#ServerIP = 192.168.178.111
Locals = 17020000
IgnoreList = /var/keys/ignore.list
[monitor]
Port = 8000
NoCrypt = 127.1.1.1
NoCrypt = 10.0.0.0-10.255.255.255
NoCrypt = 172.16.0.0-172.31.255.255
NoCrypt = 192.168.0.0-192.168.255.255
AULow = 120
MonLevel = 4
[newcamd]
Port = 15000@1702:FFFFF;15001@1833:FFFFF
Key = 0102030405060708091011121314
Eigentlich habe ich diese Dateien nur von Beitrag #1 kopiert und mir IP`s angepasst.
- DBoxII Sagem 1x mit NG², Keywelt-Image
- Kathrein UFS910HD, 1Watt, AAF2.0e und Winterimage2010 als BA
- Sky 4-er Paket, S02-Karte
Noch ein kleiner Zusatz, vielleicht hilft es ja?!
Unter "Features" (blaue Taste), dann "Crypt-Info anzeigen" (Taste 3)
zeigt er "0 Karten sind online"
Bei "Wer ist online ?" zeigt er meine Client's. Es wird mir sogar gezeigt, wer online ist, aber alles dunkel!
Unter "Features" (blaue Taste), dann "MPCS-Monitor" (Taste 0) wird in den einzelnen Spalten nichts angezeigt!
Hm ... keiner mehr da? Ich habe die gleichen Einstellungen - bei mir läuft es auch nicht. Ein Hinweis wäre schon nicht schlecht. Ich weiß echt nicht, was man noch ändern könnte.
Vielen Dank!
Gruß
Ich will mal nicht so sein ,hier mal die am Anfang beschriebene Konfiguration in einem 2X image ohne cwshare und natürlich ohne Kekse,die in einer vernünftigen Share eh nichts zu suchen haben.
Das Image ist lauffähig,nachdem Ihr eine cwshare.cfg erstellt und eingefügt habt,die Konfiguration stellt eine Grundkonfiguration dar ,die der entsprechenden Share und Karte angepasst werden sollte.
http://rapidshare.com/files/19484100...ne-cwshare.rar
Cool - DANKE !!!
Ich werde es gleich mal probieren
geht !!!
Danke!
Hallo nochmal, also hab jetzt mbox überschrieben, lauft, aber wenn ich mit open port check tool die drei ports teste,kommt komischerweise nur port 21 und 23 durch. der dritte port, den hab ich auf 2500 gesetzt da bekomm ich immer diese meldung
Error: I could not see your service on xx.xxx.xxx.xx on port (2500)bei den zwei anderen sitz so aus
Success: I can see your service on xx.xxx.xxx.xx on port (23, und 21)kann mir da noch mal geholfen werden?
bei mbox.cfg hab ich den Z: wert so gestzt
Z: { 12 } { 192.168.178.8 2500 }hab aber auch die gleiche einstellung mit der dns adresse oder mit 127.0.0.1 probiert und auf meiner fritzbox hab ich selbstverständlich port 2500-2509 durchgestellt. Es geht nicht
hallo zusammen
möchte nochmal meine aktuellen kofigs für die kathi hier reinstellen.
ich glaub es ist schon besser port 21 und 23 wird weiter geleitet nur port 2500 noch nicht.möchte auch meine karte ansprechen da sie ja auch an meinen g-line partner geshart werden müssen,oder?
Bitte helft mir nochmal
Möchte das forum nicht so voll pumpen deshalb als anhang mbox.cfg und cwshare.cfg,hab nur die beispiel m-line in cwshare wegen platz nach unten verschoben
DANKE
nils22
so hab ich die zwei dateien jetzt auf der kathi
Geändert von nils22 (03.03.09 um 01:01 Uhr)