DBOX2 Mastercrd und NDS V13 funzt nicht -:(

hansie45 · 21.11.08

Reader falsch konfiguriert, Du hast ja kein Multicam sondern einen Phoenixreader, hier ein Beispiel:

<device>
<name>phoenix</name>
<type>Phoenix</type>
<node>/dev/tts/0</node>
<mhz>357</mhz> 
<parity>even</parity>
<reset>normal</reset>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<****detect>yes</****detect>
<newcamd_port>*****</newcamd_port>
<priority>round</priority>
<autosid>Yes</autosid>
</device>

**heisse_fee** · 21.11.08

Mmhh. Ist ja witzig. Wenn ich hier Dir Antworte sehe ich Deine Config.

Confused

O.k. der Eintrag ist doch egal, oder:
<name>Multicam</name>
<type>Phoenix</type>

Oder spielen die tatsächlich eine Rolle.
Und nach langem lesen bin ich der Meinung, dass ich den externen Reader über /dev/tts/0 anspreche.

Bitte klärt mich auf

**heisse_fee** · 21.11.08

Nun habe ich mal meine newcs.xml geändert:

Code:

<newCSconfig>
	<readers name="DBox2">
		<device>
			
			<name>phoenix</name>

			
			<type>Phoenix</type>

			
			<mhz>357</mhz>

			
			<node>/dev/tts/0</node>

			
			<parity>even</parity>

			
			<reset>normal</reset>

			
			<export>Yes</export>

			
			<enabled>Yes</enabled>

			
			<blocksa>No</blocksa>

			
			<blockua>No</blockua>

			
			<blockga>No</blockga>

			
			<boxkey>00000000</boxkey>

			
			<irdeto-camkey>0000000000000000</irdeto-camkey>

			
			<irdeto-camkey-data>0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000</irdeto-camkey-data>

			
			<crypto-special>No</crypto-special>

			
			<ipk>0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000</ipk>

			
			<ucpk>0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000</ucpk>

			
			<PTShandshake>No</PTShandshake>

			
			<****detect>yes</****detect>
			
			<crypto-special>no</crypto-special>

			
			<newcamd_port>34001</newcamd_port>

			
			<autosid>Yes</autosid>

			
			<Seca-PPV>no</Seca-PPV>

			
			<priority>round</priority>
		</device>
	</readers>
	<cache>
			
			<emm>20</emm>

			
			<ecm>-1</ecm>
	</cache>
	<debug>
			
			<mode>simple</mode>

			
			<level>normal</level>

			
			<type>init</type>

			
			<output>console,tcp</output>

			
			<console_options>normal,init</console_options>

			
			<tcp_port>10001</tcp_port>

			
			<tcp_options>normal,init</tcp_options>
	</debug>
	<newcamdserver>
			
			<enabled>Yes</enabled>

			
			<name>newcs</name>

			
			<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>

			
			<user><status>access</status>
				
				<name>newcs1</name>

				
				<password>newcs</password>

				
				<hostname>192.168.1.8</hostname>

				
				<au>on</au>

				
				<sidoverride>off</sidoverride>

				
				<spider>off</spider>

                                
                                <rate>2</rate>
			</user>
	</newcamdserver>
	<httpd>
<server>
<port>8088</port>
<enabled>yes</enabled>
</server>
<user>
<name>Admin</name>
<password>0815</password>
<accesslevel>admin</accesslevel>
</user></httpd></newCSconfig>

Hier das Ergebnis im Log:

Code:

BusyBox v1.7.2 (2008-10-30 00:59:12 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/var # killall -9 newcs
/var # newcs
This is NewCS 1.62 - the New ****Server by the Butter-team..
Compiled on Aug 27 2008 at 16:49:31
Reading Config file from /var/tuxbox/config/newcs.xml
TCP-log password is disabled!
level: normal
type: init
output: console,tcp
logger config: level 1 type 3 output 5
Console log options: level 1 type 3
TCP log options: level 1 type 3
[ 20:21:20 ] [ Box detect ] Box type 4 (Dbox2)
[ 20:21:20 ] [ Config ] Option <blockc0> for device 0 (phoenix) not present, defau
[ 20:21:20 ] [ Config ] Value in <ipk> for device 0 (phoenix) is INVALID, skipping
[ 20:21:20 ] [ Config ] Value in <ucpk> for device 0 (phoenix) is INVALID, skippin
[ 20:21:20 ] [ Config ] /dev/tts/0 ECM priority: round
[ 20:21:20 ] [ httpd ] httpd-user: Admin, password: 0815, accesslevel: admin
[ 20:21:20 ] [ EMM Cache ] Initialising dynamic Cache
[ 20:21:20 ] [ ECM Cache ] Initialising dynamic Cache
[ NewCS ] Process ID is: 5021
[ 20:21:21 ] [ Loader ] Starting Telnet on port 10001
[ 20:21:21 ] [ Loader ] Started HTTP-server on port: 8088
[ 20:21:21 ] [ Loader ] Reader type 2 on node /dev/tts/0
[ 20:21:21 ] [ Phoenix ] Opening device /dev/tts/0
[ 20:21:21 ] [ Phoenix ] Setting Parity to: EVEN
[ 20:21:21 ] [ Phoenix ] Setting 2 Stop bits on node /dev/tts/0
[ 20:21:21 ] [ Phoenix ] Setting Baud to standard 9600
[ 20:21:21 ] [ Phoenix ] Normal RESET on node /dev/tts/0
[ 20:21:23 ] [ Loader ] Reset failed ...
[ 20:21:23 ] [ Loader ] Starting Newcamd Server on port 34001
[ 20:21:23 ] [ NewCS ] Ready to GO! :)
/var # [ 20:21:23 ] [ Newcamd ] Newcamd thread Server started on port 34001
[ 20:21:23 ] [ Loader ] Reader type 2 on node /dev/tts/0
[ 20:21:23 ] [ Phoenix ] Opening device /dev/tts/0
[ 20:21:23 ] [ Phoenix ] Setting Parity to: EVEN
[ 20:21:23 ] [ Phoenix ] Setting 2 Stop bits on node /dev/tts/0
[ 20:21:23 ] [ Phoenix ] Setting Baud to standard 9600
[ 20:21:23 ] [ Phoenix ] Normal RESET on node /dev/tts/0
[ 20:21:25 ] [ Loader ] Reset failed ...
[ 20:21:25 ] [ Loader ] Reader type 2 on node /dev/tts/0
[ 20:21:25 ] [ Phoenix ] Opening device /dev/tts/0
[ 20:21:25 ] [ Phoenix ] Setting Parity to: EVEN
[ 20:21:25 ] [ Phoenix ] Setting 2 Stop bits on node /dev/tts/0
[ 20:21:25 ] [ Phoenix ] Setting Baud to standard 9600
[ 20:21:25 ] [ Phoenix ] Normal RESET on node /dev/tts/0
[ 20:21:26 ] [ Loader ] Reset failed ...
[ 20:21:26 ] [ Loader ] Reader type 2 on node /dev/tts/0
[ 20:21:26 ] [ Phoenix ] Opening device /dev/tts/0
[ 20:21:26 ] [ Phoenix ] Setting Parity to: EVEN
[ 20:21:26 ] [ Phoenix ] Setting 2 Stop bits on node /dev/tts/0
[ 20:21:26 ] [ Phoenix ] Setting Baud to standard 9600
[ 20:21:26 ] [ Phoenix ] Normal RESET on node /dev/tts/0
[ 20:21:28 ] [ Loader ] Reset failed ...
[ 20:21:28 ] [ Loader ] Reader type 2 on node /dev/tts/0
[ 20:21:28 ] [ Phoenix ] Opening device /dev/tts/0
[ 20:21:28 ] [ Phoenix ] Setting Parity to: EVEN
[ 20:21:28 ] [ Phoenix ] Setting 2 Stop bits on node /dev/tts/0
[ 20:21:28 ] [ Phoenix ] Setting Baud to standard 9600
[ 20:21:28 ] [ Phoenix ] Normal RESET on node /dev/tts/0
[ 20:21:29 ] [ Loader ] Reset failed ...
[ 20:21:29 ] [ Loader ] Reader type 2 on node /dev/tts/0
[ 20:21:29 ] [ Phoenix ] Opening device /dev/tts/0
[ 20:21:29 ] [ Phoenix ] Setting Parity to: EVEN
[ 20:21:29 ] [ Phoenix ] Setting 2 Stop bits on node /dev/tts/0
[ 20:21:29 ] [ Phoenix ] Setting Baud to standard 9600
[ 20:21:29 ] [ Phoenix ] Normal RESET on node /dev/tts/0
[ 20:21:31 ] [ Loader ] Reset failed ...
[ 20:21:31 ] [ Loader ] Reader type 2 on node /dev/tts/0
[ 20:21:31 ] [ Phoenix ] Opening device /dev/tts/0
[ 20:21:31 ] [ Phoenix ] Setting Parity to: EVEN
[ 20:21:31 ] [ Phoenix ] Setting 2 Stop bits on node /dev/tts/0
[ 20:21:31 ] [ Phoenix ] Setting Baud to standard 9600
[ 20:21:31 ] [ Phoenix ] Normal RESET on node /dev/tts/0
[ 20:21:32 ] [ Loader ] Unknown ****
[ 20:21:32 ] [ Loader ] Trying Irdeto (T=14)
[ 20:21:32 ] [ Loader ] Reader type 2 on node /dev/tts/0
[ 20:21:32 ] [ Phoenix ] Opening device /dev/tts/0
[ 20:21:32 ] [ Phoenix ] Setting Parity to: EVEN
[ 20:21:32 ] [ Phoenix ] Setting 2 Stop bits on node /dev/tts/0
[ 20:21:32 ] [ Phoenix ] Setting Baud to custom 5713
[ 20:21:32 ] [ Phoenix ] Normal RESET on node /dev/tts/0
[ 20:21:34 ] [ Loader ] Reset failed ...
[ 20:21:34 ] [ Loader ] Starting Newcamd Server on port 34001
[ 20:21:34 ] [ Newcamd ] Newcamd thread Server started on port 34001
[ 20:21:34 ] bind: error! 98: Address already in use

Leider immer noch kein Bild :-(

**heisse_fee** · 21.11.08

@hansi45

Schon mal besten Dank für Deine Hilfe. Bin schon ca. 1 Woche am Basteln. Aber ich bekomme einfach kein Bild.

So nun habe ich Deine xml übernommen. Sieht nun so aus:

Code:

<device>
<name>phoenix</name>
<type>Phoenix</type>
<node>/dev/tts/0</node>
<mhz>357</mhz> <!-- oder 600 -->
<parity>even</parity>
<reset>normal</reset>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<PTShandshake>no</PTShandshake>
<crypto-special>no</crypto-special>
<****detect>yes</****detect>
<newcamd_port>34001</newcamd_port>
<priority>round</priority>
<autosid>Yes</autosid>
</device>

Leider auch kein Bild

Letzte Themen:

Thema: DBOX2 Mastercrd und NDS V13 funzt nicht -:(

Themen-Optionen

Thema durchsuchen

Anzeige

Hybrid-Darstellung

Ähnliche Themen

Mastercrd 2 an dbox2

CS mit Dbox2 und mastercrd!Hilfee

Berechtigungen