wie muss man jetzt die .conf Datei bearbeiten von 0.82 , die ist ja nicht mehr ganz identisch mit 0.55.
ist adapter1 in dvb anlegen jetzt wichtig ?
mfg
wie muss man jetzt die .conf Datei bearbeiten von 0.82 , die ist ja nicht mehr ganz identisch mit 0.55.
ist adapter1 in dvb anlegen jetzt wichtig ?
mfg
Topfield 7700HDPVR mit Enigma2
NAbend
Glaubt mir, ich habe in den letzten Tagen alles versucht incubus mit cccam zu verbinden - ohne Erfolg.
Die line läuft jedoch aufm PC mitFlycccam.
Kann es sein, dass incubus nach einer gewissen Zeit den Verbindungsversuch abbricht, weil die Inet-verbndung zu langsam ist?
Habe 2-Wege sat über Filiago, da kein DSL anliegt.
CS über PC (Skystar, ProgDVB und Flycccam) geht geradeso, wenn keine andere Anwendung auf das Inet zugreift.
Ich gebs sonst auf, weil ich zu blöd bin.
Batan
Läuft damit HD ?
Hallo,
Ich habe jetzt alles so wie von euch beschrieben gemacht, leider bleibt alles
dunkel. Verbindung zum Server ist da aber das Bild kommt nicht.
Ich habe das schon mit neustem PKT und AAF probiert aber ohne Erfolg.
Vieleicht kann jemand, was Incubus 0.82 zum Laufen gebracht hat paar Tipps
geben oder eine conf und prio Beispiel posten. Server läuft mit cccam.
Es gibt in Incubus 0.82 Package eine Datei Softcam.key die gabst bei 0.55 nicht.
Ist dieser Datei für cs wichtig?
Gruß
Aleks
Hi zusammen,
ich versuche gerade die incubus 0.82 auf ner Kathi mit meiner Dreambox per CCcam Protokoll zu verbinden wo meine S02 Karte drinnen steckt. Auf der Dream rennt CCcam 2.1.0. Ich bekomme nen Connect aber das Bild bleibt schwarz.
Meine Config:
CCcam.cfg
Zitat:
F: kathi kathi 3 0 0 { 0:0:3 } #kathi
incubuscamd.config
Zitat:
[Prov:000000:CaID:0000]
decoder_type=1
card_server_url_0=cccam://kathi:kathi@192.168.2.100:33456
[Servers]
card_server_url=cccam://kathi:kathi@192.168.2.100:33456
Hat jemand nen Tip für mich?
Gruß
Jupp hast Recht, funktioniert mit 2.011. :-)
Hat schon jemand die HD per Tunneling hell bekommen? Bei mir klappts net!!!
Gruß
Ob Hd geht, möchte ich auch gerne wissen.
Hat jemannd einen Tip ?
Danke
Ich bekomms net hin, Incubus scheint auch falsch am server anzufragen:
|kathi1 |192.168.2.209 |00d 00:04:15|00d 00:01:12|30 (24) |0 (0)|2.1.0 |1702:000003:0082 (nok)
man bekommt hd schon hell mit 0.55. jedoch nur wenn der server ne nds karte karte hat. s02 karten also nagra geht nicht.
Eigentlich müßte HD funktionieren, wenn der cccam Server die Daten über einen Cardserver bekommt,
der das Mapping beherrscht. (wie zum Beispiel MPCS)
Weiß echt nicht mehr weiter versuche schon seit einigen Stunden incubus0.55 auf einem
AAF Black Perl Image7 AAF_M569_Rev_1049 zum laufen zu bringen.
Hab folgendes gemacht und zwar jedes mal wenn ich im AAF Panel die den incubus emu starten möchte startet er und hört gleich wieder auf.
ich experimentiere schon die ganze Zeit mit verschiedenen Versionen, aber immer der gleiche fehler :(
weiß jetzt echt nicht mehr weiter bitte helft mir bei der konfiguration :(
Habs so konfiguriert und zwar:
zuerst einmal die emu datei in /var/emu/incubuscamd.sh4_e2 mit 755
die incubuscamd.sh4_e2.emu in /var/etc auch mit 755
die incubuscamd.conf in var/keys 755
meine incubuscamd emu datei:
#incubus Beispieldatei
emuname =incubuscamd.sh4_e2
binname =incubuscamd.sh4_e2
startcam =/var/emu/incubuscamd.sh4_e2
stopcam =killall -9 incubuscamd.sh4_e2
meine incubuscamd. conf:
################################################## ############################
# incubusCamd configuration file #
# All configuration options in this file observe the same format: #
# <configuration_name>=<configuration_value> #
# #
# Each section are [<section_name>:<option_1>:<option_x>] like. #
# #
# No matter about white spaces on any place or UNIX/DOS style files #
################################################## ############################
########################### general configuration ############################
[General]
background_execution=1
[CaID:0100]
ecm_table=80
priority=1
[CaID:0500]
ecm_table=80
priority=1
[CaID:0600]
ecm_table=80
priority=1
[CaID:0919]
ecm_table=80
priority=1
[CaID:093B]
ecm_table=80
priority=1
[CaID:0B00]
ecm_table=80
priority=1
[CaID:0D00]
ecm_table=80
priority=1
[CaID:1700]
ecm_table=80
priority=1
[CaID:1800]
ecm_table=80
priority=1
[CaID:2600]
ecm_table=80
priority=1
[Prov:0501]
[Prov:FF00]
card_server_url_0=cccam://******wx:3456walter@*********:7025
card_server_url_1=cccam://*******:qwalter600234@********:7020
[Servers]
card_server_url_0=cccam://******wx:3456walter@*********:7025
card_server_url_1=cccam://*******:qwalter600234@********:7020
sollte angeblich passen ?
Wie kann ich das am besten testen ob die Zugangsdaten am Server korrekt sind, oder ober sie überhaupt am Server connected ist ?
Bin nach Stunden Sucherei und leserei am Ende :((
Geändert von XoX360 (04.05.09 um 21:44 Uhr)
wo find ich das bitte ?
das würde mich auch interrisieren, habe genau das gleiche problem!! so bald ich meine abgeänderte conf peer ftp rüber schiebe "no CAM active" hab auch schon alles getestet, aber kp mehr an was es liegen könnte! bitte um hilfewo find ich das bitte ?
hier mal meine config!
[General]
# Enable or disable background execution of the cam
# 0 - Disable
# 1 - Enable
background_execution=1
[CaID:0100]
ecm_table=80
priority=1
[CaID:0500]
ecm_table=80
priority=1
[CaID:0600]
ecm_table=80
priority=1
[CaID:0919]
ecm_table=80
priority=1
[CaID:093B]
ecm_table=80
priority=1
[CaID:0B00]
ecm_table=80
priority=1
[CaID:0D00]
ecm_table=80
priority=1
[CaID:1700]
ecm_table=80
priority=1
[CaID:1800]
ecm_table=80
priority=1
[CaID:2600]
ecm_table=80
priority=1
[Prov:0501]
card_server_url_0=cccam://user:pass@ip.dyndns.org:12000
[Prov:FF00]
card_server_url_0=cccam://user:pass@ip.dyndns.org:12000
[Servers]
card_server_url_0=cccam://user:pass@ip.dyndns.org:12000
Hmm..
Ich hab gestern das neue PKT geladen, Incubus rein, Einstellungen von pfefferl rein, neu gestartet - und dunkel.
Incubus bleibt zumindest erstmal aktiv. Aber eben dunkel.
Line funzt aufm PC mit Flycccam
Bin nur Client
Batan
incubusCamd configuration file #
# All configuration options in this file observe the same format: #
# <configuration_name>=<configuration_value> #
# #
# Each section are [<section_name>:<option_1>:<option_x>] like. #
# #
# No matter about white spaces on any place or UNIX/DOS style files #
################################################## ############################
########################### general configuration ############################
[General]
# Enable (1) or disable (0) background execution
# 0 - Off
# 1 - On
background_execution=1
# This sets the level of console output for debugging:
# 0 - No debug messages, 1 - First level debug messages, 2 - Second level debug messages,
# 3 - Print all debug messages
debug_level=1
# This option enables (1) or disables (0) the writing of debug information to the
# console.
log_to_console=1
# This option enables (1) or disables (0) the writing of console output to a log file
log_to_file=0
# When log_to_file is set to 1, this is the path and filename to write console
# ouput to.
logfile_name=/var/bin/incubusCamd.log
# Used to activate on-screen messages. Username and password required if
# HTTP authentication is enabled on enigma.
on_screen_messages_show=0
on_screen_messages_username=root
on_screen_messages_password=
on_screen_messages_key_update=0
on_screen_messages_wait_for_key_update=0
on_screen_messages_ecm=0
on_screen_messages_emm=0
#When activated, camd will listen on the specified port for connections. All
#log activity will be broadcast in real-time to connected clients.
console_logs_broadcast=1
console_logs_broadcast_port=666
############################ caid configuration ##############################
#
# First of all the cam use the incubusCamd.prio file, then use the
# configuration below.
# Sections are defined by the value of the CaID.
# You can choose the default ecm table used by the codify, this means that
# you can choose the first byte of the raw ecm that is downloaded from sat.
# If you don't know what value to insert, use "80". (all value are in hex)
# Default value for ecm_table is 0x80.
# The option "priority" tells if one caid should be selected before try
# another one with a priority value greater.
# The less is the value the greatest is the priority. Choose from "0" to any value,
# priority value is decimal.
#
[CaID:0100]
ecm_table=80
priority=1
[CaID:0500]
ecm_table=80
priority=1
[CaID:0600]
ecm_table=80
priority=1
[CaID:0919]
ecm_table=80
priority=1
[CaID:093B]
ecm_table=80
priority=1
[CaID:0B00]
ecm_table=80
priority=1
[CaID:0D00]
ecm_table=80
priority=1
[CaID:1700]
ecm_table=80
priority=1
[CaID:1800]
ecm_table=80
priority=1
[CaID:2600]
ecm_table=80
priority=1
########################### provider configuration ###########################
#
# All parameters are in hexadecimal notation.
# Each section is defined by the provider id value.
# If you don't know the provider id value then use the provider id "000000" and ca id "0000".
# On provider 000000 caid 0000 goes all provider wich are not declared. If the provider
# is declared then the cam will use the provider founded.
#
[Prov:000501:CaID:1833]
# ----------------------------------------------------------------------------
# Decoder type indicates whether the cam will attempt to decode this provider
# in software, or through a card-server. Supported values are:
#
# 0 - Use internal softcams.
# 1 - Connect to a card sharing protocol card-server.
decoder_type=1
card_server_url_1=cccam://txxx1:cxxxxxe no@sxxxxxxxxxxxxxxxxxg:12000
# URL of card-server to use, formats are as follows:
#
# newcamd://<username>:<password>@<hostname>:<port>/<des_key>
# aroureos://@<hostname>:<port>
# radegast://@<hostname>:<port>
#
# Example:
# newcamd://foo:bar@192.168.0.100:12345/0CE3476FF2E1C9D9A0A109B371E3
#
# Multiple card-server url's can be specified for server fail-over.
# If the emu fails to connect or fails to get valid CW's, it will try to
# connect to other servers in a round-robin fashion.
#
# Up to 16 servers can be added from index 0 to 15.
#
# You can choose also to select a cccam or gbox server, but they must be declared
# in the "servers configuration" section ( [Servers] ).
# e.g. : if you want to use a cccam server for a provider you must put it on
# the parameter card_server_url_0=cccam://
# NO MATTER the value after the double slash because server configuration is
# made in the section [Servers].
# Only for newcamd, radegast and aroureos is usefull to put correct connection
# parameters because they are provider dependent.
#
#
# Example i want to use mine card into the slot with newcs for prov 0501 on nagra3 (caid 1833)
card_server_url_0=newcamd://username:password@192.168.0.100:10550/0102030405060708091011121314
[Prov:000000:CaID:0000]
card_server_url_0=cccam://txxx1:cxxxxxe no@sxxxxxxxxxxxxxxxxxxxxg:12000
# this provider is a stand-in for all cards and all caid not declared previously
#
# For example I choose to use cccam protocol on all other provider.
#
decoder_type=1
card_server_url_0=newcamd://kati:kati@127.0.0.1:10000/0102030405060708091011121314
card_server_url_0=cccam://txxx1:cxxxxxe no@sxxxxxxxxxxxxxxxxxxg:12000
########################### servers configuration ############################
[Servers]
#
# This is the section for the multi-server configuration.
#
# URL of card-server to use, formats are as follows:
#
# cccam://<username>:<password>@<hostname>:<port>/<receive_emu_shared>/[EMM]
# where <receive_emu_shared> should assume value "yes" (without quotes, if you like to receive emus data shared by the server) or "no" (this is assumed by default)
#
# gbox://<localhost>:<localport>:<password>@<peer_address>: <peer_port>:<peer_pass>/[EMM]
#
# NOTE: The "EMM" suffix is optional and tells the card-server client whether
# to send EMM's to the card-server or not. Enabling or disabling this only
# has effect if the card-server is configured to accept emms from this client.
#
# NOTE 2: The "card_server_url" is not the same as previously declared in the prov/caid section
# use how many server as you like
#
#card_server_url=cccam://<username>:<password>@<hostname>:<port>
#card_server_url=gbox://<localhost>:<localport>:<password>@<peer_address>: <peer_port>:<peer_pass>
#card_server_url=cccam://<username>:<password>@<hostname>:<port>
#card_server_url=gbox://<localhost>:<localport>:<password>@<peer_address>: <peer_port>:<peer_pass>
########################### CaIDs tunneling configuration ############################
[CaIDTunnel]
#
# All values are in hex notation
# In this file you can configure what CAIDs/PIDs incubusCamd should tunnel to another CAID
#
# situation 1: this caid, all idents, on all channels will use the tunnel_caid
# caid:tunnel_caid
#
# situation 2: this caid/ident pair will use the tunnel_caid
# caid:tunnel_caid:ident
#
# situation 3: this caid/ident pair, on channel 'sid' will use the tunnel_caid
# caid:tunnel_caid:ident:sid
#
# i.e:
# 1833:1702:000000:0082 # this one should tunnel premiereHD nagra3 into betacrypt cards
# 1833:1702:000000:0081 # this one should tunnel premiereHD nagra3 into betacrypt cards
#
Geändert von Yabbadoo (05.05.09 um 09:58 Uhr)