Soooo...
Wer von euch auch das wundervolle Neutrino auf der Kathi hat, und mgcamd einbauen möchte, hier mal meine configs.
Configs wurden angepasst. Alle CAID´s laufen. Dank an Reus! :liebe0090:
1. Die mgcamd 1.35 aus diversen Foren laden, "mcgamd.sh4" nehmen, das ".sh4" entfernen und per FTP nach var/emu kopieren. (Rechte 755)
2. Die mg_cfg datei nach var/keys kopieren.
3. Die datei newcamd.list nach var/keys kopieren.Zitat:
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 00 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30
# network ecm timeout in seconds
K: { 05 }
# newcamd dead routes connect retry, sec
Q: { 300 }
# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 02 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 11 }
# map all 180x nagra caids to 1801
# default is 01
F: { 00 }
4. ****Entfällt**** Die datei replace.list nach var/keys kopieren. (Angeblich wegen HD Kanälen. Da bei mir nur die CAID 1702 geht, kann ich leider nicht bestätigen...)Zitat:
CWS = 192.168.178.100 15000 HD-Kathi0 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15001 HD-Kathi1 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15002 HD-Kathi2 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15003 HD-Kathi3 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15004 HD-Kathi4 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
5. Die datei newcamd.conf nach var/tuxbox/config kopieren.Zitat:
# replace old with new {{ sid } { caid } { provid } { ecmpid } { newcaid } { newprovid } { newecmpid }}
# multivision 1 example
# R: {{ 515 } { 500 } { 7C00 } { A0 } { 500 } { 7800 } { A1 }}
# OR put this ecm on top if new* = 0
# R: {{ 515 } { 500 } { 7800 } { A1 } { 0 } { 0 } { 0 }}
# replace old caid > newcaid example
# X: {{ 624 } { 604 }}
X: {{ 1833 } { 1702 }}
Zitat:
# /var/tuxbox/config/newcamd/newcamd.conf
#
# newcamd mandatory settings
#
# Use emulator?
EMU = no
# if both control word server and emulator keys are available for the
# channel, which method should be tried first?
PREFER_EMU = no
# Autoupdate for Emu and Control Word Servers
# AU is always yes if there are betad UDS control word server
# connected to newcamd
AU = yes
#
# OSD
#
# number of seconds to show the newcamd OSD, works on enigma only
# 0 seconds -> OSD off
# 1 second -> show "Can't decode" messages only
OSD_TIMEOUT = 0
# Recent Enigma versions come with a new option "Use http authentication"
# in the Expert Setup menu. If this option is enabled, the Enigma web server
# requires all clients to authorize themselves with username (root) and
# password (usually dbox2 or dreambox). The following option tells newcamd
# about the authentication username and password to use for the web server
# in order to be able to display its on screen information.
OSD_WEB_LOGIN = root:dbox
#
# newcamd debug options
#
# dumps all ca systems used by a channel on the console
SHOW_ALL_CA_SYSTEMS = no
# print debug messages about ECM handling
DEBUG_ECM = yes
# print debug messages about EMM handling
DEBUG_EMM = yes
# print debug messages about Control Word Server (CWS)
DEBUG_CWS = yes
# print debug messages about dbox2 CAM (cam-alpha.bin)
DEBUG_CAM = yes
# hex dump of entire PAT
SHOW_PAT = no
# hex dump of entire PMT
SHOW_PMT = no
# hex dump of entire ECM
SHOW_ECM = no
# hex dump of entire CAT
SHOW_CAT = no
# hex dump of entire EMM (AU)
SHOW_EMM = no
# show network ECM messages being sent and received from/to the cardservers
SHOW_CWS_ECM = no
# show network EMM messages being sent and received from/to the cardservers
SHOW_CWS_EMM = no
# hex dump of EMMs with wrong signature
EMM_REPORT_WRONG_SIG = no
#
# newcamd optional settings
#
# Delay between reception of new control word and writing them into
# the CSA registers
# this is a default, can be changed for each individual key in keylist
DEFAULT_CW_DELAY = 0
# reload config on every channel zap
RELOAD_CONFIG_ON_ZAP = yes
# reload keylist on every channel zap
RELOAD_KEYLIST_ON_ZAP = no
# write osd ca info to file
CA_INFO_FILE = /tmp/cainfo.txt
#
# newcamd mandatory settings for control word servers (cws)
#
# Cardserver list
#
# <hostname> <port> <username> <password> <14 byte triple-des key in hex> <lan/wan> <cardserver name> [noecm]
#
# wan connections will be dropped and rebuild if newcamd is told so by camdcmd
# (see admin options)
#
# If the last word in the CWS line is noecm, newcamd will not attempt to send
# any ecms to that card, it will only send EMMs (AU) if userid is 1. Useful if
# you want to merge several cards of one provider into one port using
# cardspider.
#
# hostname = uds to use betad, port is the serial port in that case
#
# CWS = uds 1 dummy dummy
# CWS = linux.domain.com 10000 dummy2 dummy2 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserv
# CWS = 127.0.0.1 10000 dummy3 dummy3 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserv
#CWS = uds 0 local local
CWS = 192.168.178.100 15000 HD-Kathi0 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15001 HD-Kathi1 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15002 HD-Kathi2 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15003 HD-Kathi3 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
CWS = 192.168.178.100 15004 HD-Kathi4 UFS-910 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan oscam
#
# newcamd optional settings for using control word servers (cws)
#
# Timeout for cardserver login in 100ms
CWS_CONNECT_TIMEOUT = 20
# Port to listen for incoming cardserver connections (reverse login)
# and/or admin connections
CWS_INCOMING_PORT = 21000
# Port to get a list of all connected cardservers, just telnet to it
CWS_DEBUG_PORT = 12001
# send keep alive messages to servers to keep connections from dying by
# unreasonable router NAT timeouts, make sure all cardservers/spiders you
# conntect to are v5.25 or newer, otherwise you'll loose connection to them,
# if set to yes
# seems this feature is commonly misunderstood, it only keeps connections
# open even if no data packets are using it for while (NAT routers tend to
# forget about established tcp connections when they are inactive), it is
# NOT to automatically reconnect to servers, see also Q&A in readme.txt
CWS_KEEPALIVE = yes
#
# newcamd admin control options
# (incoming port is the same as CWS_INCOMING_PORT)
#
# <password> <14 byte des key>
#
ADMIN_PASSWORD = 0102030405060708091011121314
So, das war´s soweit für die Kathi!
Nun muss man noch die oscam in seinem Server kofigurieren.
6. Die datei oscam.conf sieht so aus:
7. So die oscam.user:Zitat:
[global]
Nice = -1
ClientTimeout = 5
CacheDelay = 120
Level = 15
BindWait = 10
LogFile = /dev/null
[monitor]
Port = 988
NoCrypt = 127.1.1.1
NoCrypt = 10.0.0.0-10.255.255.255
NoCrypt = 172.16.0.0-172.31.255.255
NoCrypt = 192.168.0.0-192.168.255.255
AULow = 120
MonLevel = 4
[newcamd]
Key = 0102030405060708091011121314
Port = 15000@1830:000000
Port = 15001@1702:000000
Port = 15002@0D05:000004
Port = 15003@1833:000000
Port = 15004@0500:023800,042200,023B00,024400
# -- camd 3.5x ----------------------------------------------------------------
# Port : Port-Number (0 disables this protocol)
# ServerIP : bind service to ONE dedicated ip-address
# -----------------------------------------------------------------------------
[cs378x]
Port = 54343
[cs357x]
Port = 20197
8. Nun noch die oscam aufm Server neu starten, und auf der Kathi unter "blaue Taste" das mgcamd.Zitat:
[account]
User = HD-Kathi0
Pwd = UFS-910
CAID = 1830
Group = 3
MonLevel = 4
Uniq = 1
[account]
User = HD-Kathi1
Pwd = UFS-910
CAID = 1702
Group = 1,3
MonLevel = 4
Uniq = 1
[account]
User = HD-Kathi2
Pwd = UFS-910
CAID = 0D05
AU = mastercrd
Group = 4
MonLevel = 4
Uniq = 1
[account]
User = HD-Kathi3
Pwd = UFS-910
CAID = 1833
Group = 3
MonLevel = 4
Uniq = 1
[account]
User = HD-Kathi4
Pwd = UFS-910
CAID = 0500
Group = 3
MonLevel = 4
Uniq = 1
Dann sollte es hell werden.
Wer mir jetzt noch sagen kann, wo mein Fehler liegt, warum bei mir nur die 1702 hell wird, der bekommt 100 Punkte!!! :natur0192:
P.S. Die "Group" in der oscam.user muss jeder für sich separat anpassen! Bei mir kommen manche CAID´s von ein und demselben Server, deshalb die doppelten Einträge.
Hoffe ich konnte so manchen hier helfen, die sich auch das mgcamd manuell einpflanzen müssen! :durcheinander-ersta
