NEU !
Hat das schon jemand drauf und/oder kann berichten ?
Druckbare Version
NEU !
Hat das schon jemand drauf und/oder kann berichten ?
Ist schon Geil, ich dachte auch ich sehe nicht richtig.
Hier das Release
http://www.****upload.com/?d=Z6G2KCUI
The provided image is based on the Linux operating system and includes
the Enigma2 PVR application. Please read this document carefully before
installing the image.
Unsupported features and known problems
---------------------------------------
- CAM slots are not supported yet.
- The only supported tuner type is DVB-S2 CX24116/CX24118.
- Timeshift does not work yet.
- Rewind does not work properly. Sometimes enigma2 freezes when rewinding.
"Jump back" can be used instead (see playback keys).
- Samsung LCD TVs will probably have problems with the default resolution
576i.
- There might be no video on the FIRST (!) start after installation - reboot
the box.
DISCLAIMER
----------
The software is provided 'as is' without warranty of any kind.
Please consider that you may lose manufacturer's warranty when installing
this image.
This is an alpha image. That is some functions may not be available or be
buggy (causing crashes/freezes or loss of data).
The installation of the Enigma2 image formats (ext2) the internal harddrive.
ALL FILES ON THE HARDDRIVE WILL BE LOST.
Installation instructions
-------------------------
You will need either a USB stick or a USB harddrive with FAT32 filesystem.
- Copy the files Enigma_Installer.tfd, uImage and rootfs.tar.gz to the USB
device.
- Attach the drive to the USB slot.
- Open the Topfield firmware update menu and select the image file
Enigma_Installer.tfd on the USB drive.
- Start the firmware update from USB.
- After about 6-7 minutes the installation should be finished.
DO NOT REMOVE THE USB DEVICE UNTIL the INSTALLATION HAS FINISHED.
During the installation the VFD shows the current installation step and
error messages (if any):
"9 USB STCK" mouting USB stick
"8 HDD PART" partitioning HDD
"7 HDD FMT" formatting HDD (root fs)
"6 HDD FMT" formatting HDD (data fs)
"5 HDD SWAP" creating swap
"4 ROOT FS" installing root file system
"3 LOADER" flashing U-Boot settings
"2 KERNEL" flashing kernel
"1 FSCK" checking file system
"0 REBOOT" rebooting within 2 seconds
It is recommended to attach a cable to the serial port and log the output in a
terminal program (e.g. TeraTerm) during the installation and the first start.
The USB filesystem should be writable to prevent infinite installation loop.
(The file uImage is renamed to avoid the infinite loop.)
The first start usually takes approximately 3 minutes due to creation of
device nodes.
Enigma2 can be removed by flashing a regular Topfield firmware image using
standard tools like TFD-Down or VegaPack.
First start
-----------
On the first start the Enigma2 interactively configures the video output to be
used. The following options are available:
- Component
- HDMI
- Scart
- HDMI-PC
Each connection type is switched on for 30 seconds. The VFD displays the
connection type which is currently active. You can either wait until the
connection type you want is displayed and your TV shows a picture or you
can select the connection type with Up and Down buttons on the remote control.
Confirm the desired connection type with the Ok button. After that you can
proceed with the configuration supported by the configuration wizard.
The image contains a default channel table. If you want to replace it You can
perform a channel scan later.
Network configuration
---------------------
The U-Boot settings contain the following configuration by default:
MAC address 00:3e:9e:11:22:33
IP address 192.168.178.100
That is after booting the image you can login via telnet if your computer is in
the same subnet.
These values are set up by the U-Boot. You can temporarily change the values
in Enigma2 menu "Settings/System/Network.../Adapter settings" or change the
U-Boot parameters.
Default U-Boot bootargs:
ba1=console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=192.168.178.100:192.168.178.10:192.168.178.10:2 55.255.255.0:tf7700:eth0:off nwhwconf=device:eth0,hwaddr:00:3e:9e:11:22:33
mem=128m bigphysarea=4000 coprocessor_mem=4m@0x10000000,4m@0x10400000
To change the IP addresses interrupt the U-Boot countdown and execute the
following command with replaced IP addresses:
TF7700> set ba1 'console=ttyAS0,115200 root=/dev/sda1 rw init=/bin/devinit ip=<own IP>:<server IP>:<DNS IP>:255.255.255.0:tf7700:eth0:off nwhwconf=device:eth0,hwaddr:00:3e:9e:11:22:33
mem=128m bigphysarea=4000 coprocessor_mem=4m@0x10000000,4m@0x10400000'
Please note that the setting has to be split in two lines to bypass the
limitation of U-Boot. The second line must start with a white space. The
string is enclosed in single quotes. Any change is temporary unless the
settings are saved to flash using the command "saveenv". Before saving
settings to flash you should test whether the kernel boots with your settings.
Enter "boot" at the U-Boot prompt to start the kernel. (After testing the
settings without saving them you will have to enter your changes again.)
Playback keys
-------------
Play - shows the file list
Yellow - pause/unpause playback
Green - continue playback
Red - jump to the beginning
Blue - jump to the next bookmark
1/3 jump 15 seconds backwards/forwads (configurable in the settings menu)
4/6 jump 60 seconds backwards/forwads (configurable in the settings menu)
7/9 jump 5 minutes backwards/forwads (configurable in the settings menu)
Full key map can be found in the file /usr/local/share/enigma2/keymap.xml.
Team Ducktales
Hallo...
hier gibt es doch einige TF 7700HDPVR Besitzer !
Hat es noch keiner getestet ? :confused2:
Ich hab mir die firm unterdessen besorgt, aber noch nicht installiert.....
Nicht weil ich feige bin... nein, weil die HD mit ext2 neu formatiert wird... und da sind noch 600GB HD Filme drauf....
Edit by six6Zitat:
Zitat von NOLLE
Link entfernt !!!, User verwarnt!
edit off
ja, kenne ich....Zitat:
Zitat von ferdosina
Da steht aber auch noch nicht viel....:confused2:
nimm mal lieber den link raus......
Naja, auf was wartet ihr? Das ein EMU läuft, das wird sicher bald funzen. Wenn es nicht schon funzt.
So hast du bestimmt schon gelesen das erstmal nur ein Tuner unterstützt wird. Der Rest wäre mir egal.
E2 ist auf der Box der Hammer. (Sagte mir mein Kumpel)
In dem Beitrag #3Zitat:
Zitat von Klick
steht, warum ich das Image noch nicht drauf habe.....:grinsend0089:
Hallo ich habe es drauf.
zuerst sollte man wissen das das Image auf die HDD kommt und somit die ganze Platte neu formatiert wird. Es werden dann 3 Partitionen erstellt.
SDA1 für das system, sda2 für swap und sda3 für Movies.
Im flash kommt ein Boot Eintrag rein um von platte zu starten.
Man kann mit Topset 2.0 und RS232 und Nullmodem kabel das original Image wieder flashen um den boot dings wieder wegmachen.
Enigma2 hat noch bisschen Stabilität Probleme auf den Topfield
2 gleichzeitige Aufnahmen funzen nicht richtig, nur die erste läuft durch. Bei der 2ten Aufnahme wird zwar eine info abgelegt aber der inhalt ist leer.
Man kann eine Aufnahme machen(freeTV) und sonst frei zappen.
wie schon in der readme steht funzt kein timeshift und kein cam Modul.
Ansonsten funzt die Lan Schnittstelle. HD Sender laufen soweit auch ohne Probleme.
Mit der Kanalsuche habe ich so meine Probleme und werden nicht alle Sender gefunden.
Aber es gibt ja genügend fertige enigma2 Settings die man verwenden kann.
Frage zu emu.
ja gibt es habe da einiges ausprobiert.
Der Topfield hat einen STI chipsatz und alles was auf STI_linux läuft geht auch mit der Box. Da muss man mal ein blick in den UFS910 bereich reinschauen. Nur ist die Datenstruktur nicht identisch des UFS 910. Ich musste die Camd3 und alle andere Dateien in eine, Ordner /var/bin einfügen und aus dem Verzeichnis starten. Da ich wenig erfahrung habe würde ich gerne das optimieren und einen Autostart des Emu machen. Brächte da Hilfe wie man das macht.
Leider habe ich kein twin support mit dem Emu. Cardsharing sollte auch funzen.
Wie gesagt dieses Image ist die erste veröffentlichte Beta für den 7700HDPVR.
Wer eine zuverlässige box haben will sollte vielleicht noch etwas warten.
Aber wer mal mit testen und rumspielen will kann da gerne zugreifen.
MFG
so langsam wirds mit unserem Topf....:elefant:
################################################## #######
# #
# Team Ducktales' Enigma2 image for the TF7700HDPVR #
# #
# Release 0.2 #
# #
################################################## #######
The provided image is based on the Linux operating system and includes
the Enigma2 PVR application. Please read this document carefully before
installing the image.
New features and bugfixes (since 0.1)
-------------------------------------
+ Feature: first beta support for CAMs (upper slot only)
+ Feature: added flashing topfield.tfd (if present on the USB stick) to
make going back to Topfield firmware easier
+ Feature: freed 16 MB of unused RAM
+ Feature: migrated system partition to ext3 filesystem
+ Feature: migrated to stlinux-2.6.17.14-0041
+ Feature: installation control file (noformat, noupdate, nopartition,
keepsettings, usbhdd)
+ Feature: enabled installation to a USB HDD (option usbhdd)
+ Feature: improved emergency shutdown policy
+ Change: removed mapping of the keys V- (left) and V+ (right) to volume control
to avoid problems in various menus. The volume can now be adjusted with
the keys |< and >|.
+ Fix: the keys V-/V+ can now be used to change entries in the timer menu and
to scroll page up/page down.
+ Fix: updated the settings for Astra 19°° and added new satellites.xml for
orbital position 13.0, 19.2 and 23.5 east
+ Fix: applied the SATA patch to fix interactions with HDDs
+ Fix: fixed repeating Diseq commands delaying tuning up to 20 seconds
+ Fix: added swap to /etc/fstab
+ Fix: added the dvr1 device for recording
+ Fix: added updating the network settings to the rcS (activates the user
settings made in e2)
+ Fix: fixed the issue with "SID not found in PAT" and some scan problems
+ Fix: fixed the issue with low volume
+ Fix: improved shutdown behavior so that the PVR is not turned off before
the kernel finished unmounting file systems
+ Fix: updated Vader skin (DNS settings, timer)
+ Fix: swapped keys zapUp and zapDown
+ Fix: Daylight Saving Time
- Fix: no video on the FIRST start after installation
Unsupported features and known problems
---------------------------------------
- The only supported tuner type is DVB-S2 CX24116/CX24118.
- Timeshift does not work yet.
- Rewind does not work properly. Sometimes enigma2 freezes when rewinding.
"Jump back" can be used instead (see playback keys).
- Samsung LCD TVs will probably have problems with the default resolution
576i.
- HDD shuts down and spins up very often, workaround - disable HDD standby in
e2 settings.
- With "AC3 downmix on" there is no sound on optical when AC3 stream is
selected. With "AC3 downmix off" the system migt freeze when zapping to
channels with AC3.
- After stopping the playback of a an active recording (a kind of timeshift)
the screen remains black and does not recover until the receiver is restarted.
jepp gibt sogar 0.2.1 Bugfix zu 0.2
Zitat:
+ Fix: updated satellites.xml in /etc/tuxbox
+ Fix: changed the shutdown procedure to prevent corrupting the filesystem
+ Fix: fixed minor issues with tuxtxt
+ Fix: fixed minor issues in CAM handling
+ Fix: fixed the issue with e2 settings not saved during an update or
reinstallation
:div191:
Hat sich das noch jemand angetan das enigma2 ?
ja......:hey:Zitat:
Zitat von PeterPan4711
und wie findest du es ?Zitat:
Zitat von NOLLE
Zitat:
Zitat von NOLLE
Ich war der Ersteller..... und hatte gefragt ! :natur0187856:Zitat:
Zitat von PeterPan4711
Warum ?
Na du hast ja den überblick in deinem eigenen Thraed verloren.Zitat:
Zitat von NOLLE
Ich hatte schon längst was dazu gesagt.
Und jetzt bist Du uns mal schuldig was dazu zu schreiben, da du ja gesagt hast das du es installiert hast.
Jetzt bist du dran :grinsend0296:
:grinsend0296::grinsend0296:Zitat:
Zitat von PeterPan4711
als ich fragte, hatte ich es noch nicht drauf !
Jetzt schon......021er Version
Bin für eine alpha Version ziemlich zufrieden.....
CAM geht ja jetzt auch....
2 Aufnahmen gleichzeitig gehen bei mir auch ....
Wenn man viel rumschaltet, hängt er sich manchmal auf...
Emu noch nicht installiert....
Wenn CI Modul aktiv ist, ist die Belastung der CPU sehr hoch, war bei der 02er besser....
Das sehr gute ist, dass fast alle Video Formate abgespielt werden.....
Das habe ich in der original FW mehr als vermisst....
Noch ein paar Sachen gefixt.... dann ist es super...
Wird schon.....:coole0082:
Es gibt jetzt das TDT 0.3 E² Version für den Topfield 7700 HDPVR
Ich habe es drauf gemacht und läuft recht flüssig auch Timeshift soll gehen hat aber noch paar Probleme.
Das Bild ruckeln wärend einer aufnahme ist bei mir weg.
THX TeamDuktales
Zitat:
################################################## #######
# #
# Team Ducktales' Enigma2 image for the TF7700HDPVR #
# #
# Release 0.3.0 #
# #
################################################## #######
The provided image is based on the Linux operating system and includes
the Enigma2 PVR application. Please read this document carefully before
installing the image.
New features and bugfixes (since 0.2.1)
----------------------
+ Feature: introduced MediaPlayerExtended
+ Feature: timeshift is now working (still unstable). Press pause key
to start timeshift and the stop key to stop it. Alternatively
the timeshift may be stopped by switching to another channel.
+ Feature: added DHCP support
+ Change: mountpoint for sda3 is now set to /hdd (all programs recorded
before updating will appear after installation in /hdd instead of
/hdd/movies). The change was required to host timeshift files
on the sda3 (because they are created in /media/hdd).
+ Update: incorporated the new version of stmfb v22(37)[3.1]
+ Update: added new timezones
+ Fix: fixed displaying the Dolby icon on VFD
+ Fix: fixed the link status in the network menu
+ Fix: switched subtitle color to white
+ Fix: fixed the issue with stopping playback while it is paused
+ Fix: improved audio/video resynchronization after pause
+ Fix: improved CAM handling (especially the performance)
Unsupported features and known problems
---------------------------------------
- The only supported tuner type is DVB-S2 CX24116/CX24118.
- Volume control keys
Due to an incompatibility with many menus the keys right/left cannot be used
for volume control. Therefore, the volume can be controlled via the frame
control keys |< and >|.
- Timeshift sometimes does not pause even if it shows pause sign and
the timeshift recording starts.
Workaround: switch to another channel.
- Timeshift ignores the recorded buffer if the time elapsed since
activation is less than 6-7 seconds.
Workaround: do not unpause timeshift in the first 8 seconds.
- "Fast forward" does not work properly at speeds higher than 8x.
"Jump forward" can be used instead (see playback keys).
- Rewind does not work properly. Sometimes enigma2 freezes when rewinding.
"Jump back" can be used instead (see playback keys).
- Samsung LCD TVs will probably have problems with the default resolution
576i.
- HDD shuts down and spins up very often, workaround - disable HDD standby in
e2 settings.
- With "AC3 downmix on" there is no sound on optical when AC3 stream is
selected. With "AC3 downmix off" the system migt freeze when zapping to
channels with AC3.
IMPORTANT:
When reporting problems please provide console logs documenting the system
behaviour.
Hallo
Ich bekomme mit dem TDT 0.3.0 nur incubuscamd 0.55 zum laufen.
würde gerne 0.8.3 zum laufen bekomme zb. bekomme das zwar zum "laufen" und bekomme ein connect zu CCcamd Server hin(nach mehrmaligem starten des incubus) aber der zu entschlüsselnde Film stream bleibt dunkel.
trotz die Tips aus dem UFS910 Forum. von anlegen des "adapter1" und die simu_button.ko ist im 0.3.0 schon die neue.
für Tipps wäre ich dankbar.
mfg
Es gibt eine Mod version des TDT 0.3.0 mit BluePanel
Zitat:
Enigma2 CIe2T Topfield 7700/7710 "MOD 2.0"
Modified E2 by CroTeam CIe2T
based "Team Ducktales"(Release 0.3.0 )
The provided image is based on the Linux operating system and includes
the Enigma2 PVR application. Please read "ReleaseNotesTF7700" document carefully before
installing the image.
- added blue panel
- added Mbox.emu
- fixed some bugs
- for HDPVR models (not confirmed for HSCI)
Hat denn schon jemand das bluepanel ausprobiert ?
Da ist ja bis jetzt nur "Mbox" drin, ist ja wohl für cs gedacht...
Wie bekomme ich da andere emus ( mgcam, camd3 usw. ) rein ?
oder geht das noch nicht ?
Das AAF Board baut nun auch an einem E2 Mod für den Topf auf Basis des nächsten TDT Images. Wer schon Erfahrungen mit E2 auf dem Topf gemacht hat, kann sich dort gerne als Betatester bewerben.Zitat:
Zitat von NOLLE
So jetzt wird es in gewissen Foren schon raus posaunt.
TDT 0.3.1 ist draussen beim Nachtfalken der Database.
:15:
Code:..,,,uuuuuuux-
.XJ$$$$$$$$$$$$$R"
:<???????$$$P???" ... uuuux ,ucdL
'''''` :<$$$: .dWWW>:;$$::$$F":J$$"''
,uuuouuu, .uu xcd:x$u.:J$$$ :J$P9$>;$$F.<$$h=`?$h
:$$$$$$$$$$b, .uz ucd xJ$$$:J$6d$$F':$$$F:J$P;3$>J$P.:3$,,,;J$$E
:d$$$$$$$$$$$$c::$$F;$$FJ$$P":<$$$$P` :J$$$:J$P???$>$$??:????`???"
::?"'<Xio::??$$$>J$$ :t$P;$P` :3$$P$$u::$$$P:??' `?F'
'' :d$$P `:9$$>$$F;J$><$C,,u;$$P:?$$h:3$$>
:<$$$' <8$$>$$X<J$$:<$$$$F:??' `"":J$$$
:3$$P :d$$$:$$$$$P `:???' :<P???"
::$$$' .d$$$$'`????" '::::
.:d$$6ud$$$$F
.;cJJ$$$$$$$PF'
::9$$$$$$$PF"
`'?????""''
,,, ::::::::::::..
,z$$$$$ :::::::::::::::::.
e$$$$$$$$ ::::::::::::::::::::
d$$$$$$$$$$;`::::::::::::::::::::
::."$$$$$$$$$ :::::::::::::::::::::
:::::."$$$$$$$ ::::::::::::::::::::
::::::::."$$$$$b ::''''''''':::::::'
`:::::::::`$$P" . :''''<<<<<<;. `'
`:::::::: "".,.----=--..`'<<<<<<;
`:::'',-'` .::::::::::`'- `<<<<; .::.
`,-`.::::::::::' .. `::. .:::::::::
,-'.:::::::::::' dMMMMMMx :::::` .`::::::::
,'.::::::::::::: dMMMMMMMMMM ``` JMMM `:::::
,'.:::::::::::' . MMP',ccc "MMM Mb MMMMM `:::
; :::::::::::' nM MM',$$$$$$b "Mb4M,M c,`? :'
; ::::::::::: xMMMMM'J$$$$$$$$b )MMMMM.`$$.
' :::`::::::: dMMMMM'J$$$$$$$$$$F MMMMMM $$$.
:: <`::::: JMMMMM',$$$$$$$$$$$P MMMMMM $$$$
`:::`bc,.. ,edMMMM $$$$$$$$$$$$F MMMMMM $$$$ .
` ,nMMMMMMMMTMMMM P""?$$$$$$$$".MTT4MM ?$$F;P""?x_
,d)MMMMMMP'dMMMMM $$$$$$P .cCc. $ cCc L~
,MMMMMMM ,c, 4MMr $$$$$ .CCCC> 4 CCC> L"
P)MMMMM> $$?$ "MM $$$$" CCCCC' ,, CC> % `
' MMMTMMM `b $$c.?b $$$" `CCC'-""___,,,,,__
M" `?, ??$c,,,,,,cc$7= _,cc$$$$PP"""""??$$$$
" `"b,_ "?$$$$$$$$$$P"" .. ,d"
`?$b `,,,,,,.`;;;;;;'j"
n ?$c`;;;;;;;`',;;; F
,;-;MM "$b;;;;;,,;;;'j"
,!!!!! MMMM,`?$c,_`` _,,cd'
!!!!!!!; MMMMMMn, `"""""''
. !!!!!!!!!, `"TT';!!!!>
,;!!!> !!!!!!!!!!!!! `<!!!! !;,
!!!!!!!!! '!!!!!!!!!!! !!! !!> !!!!!!;;
#########################################################
# #
# Team Ducktales' Enigma2 image for the TF7700HDPVR #
# #
# Release 0.3.1 #
# #
#########################################################
The provided image is based on the Linux operating system and includes
the Enigma2 PVR application. Please read this document carefully before
installing the image.
New features and bugfixes (since 0.3.0)
---------------------------------------
+ Feature: added support for the lower CI slot
+ Feature: more than 2 simultaneous recordings are possible
+ Feature: added VFD support for displaying some UTF-8 characters (ä, ö, ü)
+ Feature: added VFD support for displaying strings in upper case
(to display strings in lower and upper case comment out the line
"/bin/tffpctl --allcaps 1" in /etc/init.d/rcS)
+ Update: incorporated the new enigma2 version (05/30/2009)
+ Update: incorporated the new web interface version (06/04/2009)
+ Fix: disabled the HDD standby by default to avoid annoying spindowns/spinups
+ Fix: fixed the issue with multiple recordings on the same transponder
(timeshift also works while recording on the same transponder)
+ Fix: fixed fast forward for MP3 in MediaPlayer
+ Fix: increased the framebuffer memory to 12MB to allow HD skins
+ Fix: added missing file in Tuxtxt plugin
+ Fix: made timeshift start more stable
+ Fix: fixed mkv video with h264 or divx/xvid
+ Fix: reduced picture artifacts when browsing through e2 menus
Unsupported features and known problems
---------------------------------------
- The only supported tuner type is DVB-S2 CX24116/CX24118.
- Volume control keys
Due to an incompatibility with many menus the keys right/left cannot be used
for volume control. Therefore, the volume can be controlled via the frame
control keys |< and >|.
- Timeshift ignores the recorded buffer if the time elapsed since
activation is less than 6-7 seconds.
Workaround: do not unpause timeshift in the first 8 seconds.
- "Fast forward" does not work properly at speeds higher than 8x.
"Jump forward" can be used instead (see playback keys).
- Rewind does not work properly. Sometimes enigma2 freezes when rewinding.
"Jump back" can be used instead (see playback keys).
- Samsung LCD TVs will probably have problems with the default resolution
576i.
- HDD shuts down and spins up very often, workaround - disable HDD standby in
e2 settings.
- With "AC3 downmix on" there is no sound on optical when AC3 stream is
selected. With "AC3 downmix off" the system migt freeze when zapping to
channels with AC3.
- There are problems with switching between different satelleites via Diseqc.
It takes several seconds to tune to a channel on another satellite.
- Simultaneous output to HDMI and Scart is not supported.
- Sporadic hangers when zapping during an active HDTV recording
- Sporadic problems with old frames in a live stream (flashbacks)
- Under certain conditions it is possible that a transponder is blocked.
Workaround: switch to another transponder and then back.
- The receiver does not shut down after timer events when "after event"
is set to "auto".
IMPORTANT:
When reporting problems please provide console logs documenting the system
behaviour.
DISCLAIMER
----------
The software is provided 'as is' without warranty of any kind.
Please consider that you may lose manufacturer's warranty when installing
this image.
This is an alpha image. That is some functions may not be available or be
buggy (causing crashes/freezes or loss of data).
The installation of the Enigma2 image formats (ext2) the internal harddisk
unless installation on a USB HDD is selected.
ALL FILES ON THE HARDDRIVE WILL BE LOST. When reverting the installation
on the internal HDD to the original Topfield firmware all Enigma2 files
will be lost too.
Installation instructions
-------------------------
You will need either a USB stick or a USB harddrive with FAT32 filesystem.
- Copy the files Enigma_Installer.tfd, uImage, rootfs.tar.gz and
Engima_Installer.ini to the USB device. Please read the instructions
in Engima_Installer.ini on how to modify the installation process.
- Attach the drive to the USB slot.
- Open the Topfield firmware update menu and select the image file
Enigma_Installer.tfd on the USB drive.
- Start the firmware update from USB. This part is very quick.
Restart the receiver when the display shows the blinking END
- After about 6-7 minutes the installation should be finished.
DO NOT REMOVE THE USB DEVICE UNTIL the INSTALLATION HAS FINISHED or
THE INSTALLER REQUESTS TO DETACH THE USB DEVICE.
- When installing to a USB HDD (option usbhdd in Enigma_Installer.tfd)
the installer will ask you to detach the initial USB device and to
attach a USB HDD to install to.
During the installation the VFD shows the current installation step and
error messages (if any):
"9 USB STCK" mounting USB stick
"STCK DETACH" waiting for USB device to be detached (USB HDD installation)
"HDD ATTACH" waiting for USB HDD to be attached (USB HDD installation)
"8 HDD PART" partitioning HDD
"7 HDD FMT" formatting HDD (root fs)
"6 HDD FMT" formatting HDD (data fs)
"5 HDD SWAP" creating swap
"4 ROOT FS" installing root file system
"3 LOADER" flashing U-Boot settings
"2 KERNEL" flashing kernel
"1 FSCK" checking file system
"0 REBOOT" rebooting within 2 seconds
When installing to a USB HDD the contents of the internal HDD remain unchanged.
When using the option "keepsettings" in Engima_Installer.ini the newer settings
(incl. keymap.xml updates) will not be installed.
It is recommended to attach a cable to the serial port and log the output in a
terminal program (e.g. TeraTerm) during the installation and the first start.
Serial port settings: 115200, 8, N, 1.
The USB filesystem should be writable to prevent infinite installation loop.
(The file uImage is renamed to avoid the infinite loop.)
The first start usually takes approximately 3 minutes due to creation of
device nodes.
To uninstall Enigma2, copy your favorite Topfield firmware on your stick and
rename it to "topfield.tfd" (don't forget to rename uImage_ if necessary). The
installer will flash the firmware and reboot the Toppy. There have been reports
that the PVR appears to be dead for about 5 minutes until the picture comes on
the TV screen. So please be patient. Enigma2 can also be removed by flashing a
regular Topfield firmware image using standard tools like TFD-Down or VegaPack
via the serial interface.
First start
-----------
On the first start the Enigma2 interactively configures the video output to be
used. The following options are available:
- Component
- HDMI
- Scart
- HDMI-PC
Each connection type is switched on for 30 seconds. The VFD displays the
connection type which is currently active. You can either wait until the
connection type you want is displayed and your TV shows a picture or you
can select the connection type with Up and Down buttons on the remote control.
Confirm the desired connection type with the Ok button. After that you can
proceed with the configuration supported by the configuration wizard.
The image contains a default channel table. If you want to replace it you can
perform a channel scan later.
Network configuration
---------------------
The U-Boot settings contain the following configuration by default:
MAC address 00:3e:9e:11:22:33
IP address 192.168.178.100
That is after booting the image you can login via telnet if your computer is in
the same subnet.
These values are set up by the U-Boot. You can change the values
in Enigma2 menu "Settings/System/Network.../Adapter settings".
Playback keys
-------------
Play - shows the file list
Pause - pauses playback or activates timeshift
Stop - stops playback or timeshift
Record - opens the record dialog for starting stopping recording
Yellow - pause/unpause playback
Green - continue playback
Red - jump to the beginning
Blue - jump to the next bookmark
1/3 jump 15 seconds backwards/forwards (configurable in the settings menu)
4/6 jump 60 seconds backwards/forwards (configurable in the settings menu)
7/9 jump 5 minutes backwards/forwards (configurable in the settings menu)
Full key map can be found in the file /usr/local/share/enigma2/keymap.xml.
Team Ducktales
Changelog
---------
Version 0.3.0
----------------------
+ Feature: introduced MediaPlayerExtended
+ Feature: timeshift is now working (still unstable). Press pause key
to start timeshift and the stop key to stop it. Alternatively
the timeshift may be stopped by switching to another channel.
+ Feature: added DHCP support
+ Change: mountpoint for sda3 is now set to /hdd (all programs recorded
before updating will appear after installation in /hdd instead of
/hdd/movies). The change was required to host timeshift files
on the sda3 (because they are created in /media/hdd).
+ Update: incorporated the new version of stmfb v22(37)[3.1]
+ Update: added new timezones
+ Fix: fixed displaying the Dolby icon on VFD
+ Fix: fixed the link status in the network menu
+ Fix: switched subtitle color to white
+ Fix: fixed the issue with stopping playback while it is paused
+ Fix: improved audio/video resynchronization after pause
+ Fix: improved CAM handling (especially the performance)
Version 0.2.1
----------------------
+ Fix: updated satellites.xml in /etc/tuxbox
+ Fix: changed the shutdown procedure to prevent corrupting the filesystem
+ Fix: fixed minor issues with tuxtxt
+ Fix: fixed minor issues in CAM handling
+ Fix: fixed the issue with e2 settings not saved during an update or
reinstallation
Version 0.2
-------------------------------------
+ Feature: first beta support for CAMs (upper slot only)
+ Feature: added flashing topfield.tfd (if present on the USB stick) to
make going back to Topfield firmware easier
+ Feature: freed 16 MB of unused RAM
+ Feature: migrated system partition to ext3 filesystem
+ Feature: migrated to stlinux-2.6.17.14-0041
+ Feature: installation control file (noformat, noupdate, nopartition,
keepsettings, usbhdd)
+ Feature: enabled installation to a USB HDD (option usbhdd)
+ Feature: improved emergency shutdown policy
+ Change: removed mapping of the keys V- (left) and V+ (right) to volume control
to avoid problems in various menus. The volume can now be adjusted with
the keys |< and >|.
+ Fix: the keys V-/V+ can now be used to change entries in the timer menu and
to scroll page up/page down.
+ Fix: updated the settings for Astra 19°° and added new satellites.xml for
orbital position 13.0, 19.2 and 23.5 east
+ Fix: applied the SATA patch to fix interactions with HDDs
+ Fix: fixed repeating Diseq commands delaying tuning up to 20 seconds
+ Fix: added swap to /etc/fstab
+ Fix: added the dvr1 device for recording
+ Fix: added updating the network settings to the rcS (activates the user
settings made in e2)
+ Fix: fixed the issue with "SID not found in PAT" and some scan problems
+ Fix: fixed the issue with low volume
+ Fix: improved shutdown behavior so that the PVR is not turned off before
the kernel finished unmounting file systems
+ Fix: updated Vader skin (DNS settings, timer)
+ Fix: swapped keys zapUp and zapDown
+ Fix: Daylight Saving Time
- Fix: no video on the FIRST start after installation
Version 0.1
-----------
* initial release
Ja super, oder bei den HDFreaks.cc in der Database
und es geht weiter.......:zwinkernd0037:
.
Team Ducktales Enigma2 for TF7700 (0.3.2)
tdt_enigma2_4_tf7700hdpvr_0_3_2
Aus der Readme.txt des releases
----------------------------------------------------------------------
Team Ducktales' Enigma2 image for the TF7700HDPVR
Release 0.3.2
The provided image is based on the Linux operating system and includes
the Enigma2 PVR application. Please read this document carefully before
installing the image.
New features and bugfixes (since 0.3.1)
---------------------------------------
+ Feature: added support for scrolling VDF strings
(settable with the command-line tool tffpctl)
+ Fix: fixed the issue with transponder blocked by a recording
.....
.
.
und am WE ist das Erste AAF Image, basierend auf 0.3.2 online......:454:
Wau, jetzt geht die Box aber ab. Wird Zeit für den Topfield. :grinsend0229:
So das AAF_RISING_SUN_TF7700HDPVR-Beta ist jetzt draussen.
Zu finden in AFF-Board in der Database.
Code:TDT_E2_AAF_RISING_SUN_TF7700HDPVR-Beta
Danke an EME für das Bootbild und matze70 für die Settings.
Image Info
Basis TDT release 0.3.2 vom 01.07.2009
Danke an Team Ducktales für das super Basis Image und alle die dieses Image ermoeglicht und getestet haben.
AAF Erweiterungen:
+ AAF Rising Sun Bootbild
+ Brushed-Alu-HD-Skin 1.2
+ Patch 6.7.0
+ AddonManager 1.72
+ neue Settings von Matze
.
.
Kernstück ist das AAF Panel (Eigenes Menü mit erweiteren Einstellungen und Funktionen)
+ Automount für USB und eigetragene CIFS/NFS Freigaben
+ BlueKey Action (Blaue Taste selber belegbar mit Wunschplugin)
+ optionaler NTFS support
+ Optionaler Samba Server
+ USB2Serial Treiber (optional aktivierbar - für externe Kartenleser)
+ VFD Display einstellungen (momentan erstmal Uhrzeit an/aus)
+ Softcampanel (zum verwalten von Softcams)
+ AddonManager (installieren und deinstallieren von Zusatzfunktionen/Programmen)
+ UpnpFS Support
+ Fehlende Dateiendungen im MediaPlayer hinzugefügt (inklusive *.rec)
..
Viel Spaß beim Testen
Euer AAF-TDT Team
Image in der Database zu finden
hallo....
bereits seit 4 Stunden drauf....:wink2:
SUPER IMAGE !!!
Ja, aber die m-bo. funzt nicht
Stelle mal das dyndns auf nein im aaf-Panel Menü > setup > autostart.
Mit aktivierten dyndns hat es mir jedesmal die IP 192.168.178.10 rein in den nameserver1. Was zu einer sehr hohen erst ping führt, da erst versucht wird mit nict vorhanden nameserver eine anfrage zu machen.
dyndns auf aus ; nameserver1 die router IP rein, Dann mal neustarten.
so konnte ich auch das sportinfo-plugin Problem lösen, das kurz nach dem starten wieder beendet wurde.
mfg
Hallo
leider hab ich keins der angebotenen cams zum laufen gebracht (als newcs-client). Hat jemand sowas am laufen?
Versuche auch schon MgCamd ans laufen zu bekommen. Hmm, Incubus rennt auch nicht so richtig auf der kiste.
Wenn du Incubus ans laufen bekommst dann kannst du problemlos auf newcs zugreifen inclusive der Hd Kanäle.
N line eintragen in der incubus cfg
mfg
c1000
@ Klick Mgcamd läuft nicht unter Enigma.
Weisst du zufaellig welche incubus laeuft?
Das würde mich jetzt auch interessieren. Incubus habe ich am laufen gehabt, nach einer halben Stunde war schluß.
Aha, unter NewCs läuft es jetzt besser?
Das Incubus dürfte dann das 0.83 sein, oder?
MgCamd, leider ja. Ist mir auch erst am Wochenende eingefallen. Schade das die Jungs dafür nichts gemacht haben. Ich wußte nur noch das ich das mal auf ner Kathi am laufen hatte. Dann war es wohl das 2.0E vom AAF-Team.
TeamDuktales 0.4.0
Code:..,,,uuuuuuux-
.XJ$$$$$$$$$$$$$R"
:<???????$$$P???" ... uuuux ,ucdL
'''''` :<$$$: .dWWW>:;$$::$$F":J$$"''
,uuuouuu, .uu xcd:x$u.:J$$$ :J$P9$>;$$F.<$$h=`?$h
:$$$$$$$$$$b, .uz ucd xJ$$$:J$6d$$F':$$$F:J$P;3$>J$P.:3$,,,;J$$E
:d$$$$$$$$$$$$c::$$F;$$FJ$$P":<$$$$P` :J$$$:J$P???$>$$??:????`???"
::?"'<Xio::??$$$>J$$ :t$P;$P` :3$$P$$u::$$$P:??' `?F'
'' :d$$P `:9$$>$$F;J$><$C,,u;$$P:?$$h:3$$>
:<$$$' <8$$>$$X<J$$:<$$$$F:??' `"":J$$$
:3$$P :d$$$:$$$$$P `:???' :<P???"
::$$$' .d$$$$'`????" '::::
.:d$$6ud$$$$F
.;cJJ$$$$$$$PF'
::9$$$$$$$PF"
`'?????""''
,,, ::::::::::::..
,z$$$$$ :::::::::::::::::.
e$$$$$$$$ ::::::::::::::::::::
d$$$$$$$$$$;`::::::::::::::::::::
::."$$$$$$$$$ :::::::::::::::::::::
:::::."$$$$$$$ ::::::::::::::::::::
::::::::."$$$$$b ::''''''''':::::::'
`:::::::::`$$P" . :''''<<<<<<;. `'
`:::::::: "".,.----=--..`'<<<<<<;
`:::'',-'` .::::::::::`'- `<<<<; .::.
`,-`.::::::::::' .. `::. .:::::::::
,-'.:::::::::::' dMMMMMMx :::::` .`::::::::
,'.::::::::::::: dMMMMMMMMMM ``` JMMM `:::::
,'.:::::::::::' . MMP',ccc "MMM Mb MMMMM `:::
; :::::::::::' nM MM',$$$$$$b "Mb4M,M c,`? :'
; ::::::::::: xMMMMM'J$$$$$$$$b )MMMMM.`$$.
' :::`::::::: dMMMMM'J$$$$$$$$$$F MMMMMM $$$.
:: <`::::: JMMMMM',$$$$$$$$$$$P MMMMMM $$$$
`:::`bc,.. ,edMMMM $$$$$$$$$$$$F MMMMMM $$$$ .
` ,nMMMMMMMMTMMMM P""?$$$$$$$$".MTT4MM ?$$F;P""?x_
,d)MMMMMMP'dMMMMM $$$$$$P .cCc. $ cCc L~
,MMMMMMM ,c, 4MMr $$$$$ .CCCC> 4 CCC> L"
P)MMMMM> $$?$ "MM $$$$" CCCCC' ,, CC> % `
' MMMTMMM `b $$c.?b $$$" `CCC'-""___,,,,,__
M" `?, ??$c,,,,,,cc$7= _,cc$$$$PP"""""??$$$$
" `"b,_ "?$$$$$$$$$$P"" .. ,d"
`?$b `,,,,,,.`;;;;;;'j"
n ?$c`;;;;;;;`',;;; F
,;-;MM "$b;;;;;,,;;;'j"
,!!!!! MMMM,`?$c,_`` _,,cd'
!!!!!!!; MMMMMMn, `"""""''
. !!!!!!!!!, `"TT';!!!!>
,;!!!> !!!!!!!!!!!!! `<!!!! !;,
!!!!!!!!! '!!!!!!!!!!! !!! !!> !!!!!!;;
#########################################################
# #
# Team Ducktales' Enigma2 image for the TF7700HDPVR #
# #
# Release 0.4.0 #
# #
#########################################################
The provided image is based on the Linux operating system and includes
the Enigma2 PVR application. Please read this document carefully before
installing the image.
New features and bugfixes (since 0.3.2)
---------------------------------------
+ Feature: o added an extended version of TopfieldVFD plugin to
adjust VFD settings and to control additional icons
o added displaying clock and Ethernet activity
o added displaying MP3 tags
+ Feature: added handling for "auto" afterEvent in recording timer
(deepstandby after recording if woken up by a timer)
+ Feature: recognition and playback of files with the extension .rec
+ Change: reduced the guard time for shutdown prior to timer events from 360
to 60 seconds (i. e. the box can be shut down up to 60 seconds
before next recording)
+ Change: reduced the wakeup guard time from 300 to 60 seconds (i.e. the
box wakes up 60 seconds before next recording)
+ Change: moved mounting /dev/sda3 from rcS to fstab
+ Fix: improved the CAM detection
+ Fix: fixed the U-Boot handling of FAT32, now high-capacity USB sticks
should be read properly
+ Fix: fixed the issue with the MP3 playlist
+ Fix: re-added the fix to display the Dolby icon on VFD correctly
+ Fix: changed mount options to allow HDD idle without intermittent wakeups
+ Fix: removed duplicate entries in /etc/fstab
+ Fix: fixed AVI audio track selection
+ Fix: fixed playback of AVI files with 23.976fps/24.976fps/29.976fps
+ Fix: re-added the workaround to fix the issue with stopping playback
while it is paused
Unsupported features and known problems
---------------------------------------
- The only supported tuner type is DVB-S2 CX24116/CX24118.
- Volume control ****
Due to an incompatibility with many menus the **** right/left cannot be used
for volume control. Therefore, the volume can be controlled via the frame
control **** |< and >|.
- Temporary loss of sync if timeshift is unpaused within 6-7 seconds after
its activation.
Workaround: do not unpause timeshift in the first 8 seconds.
- "Fast forward" does not work properly at speeds higher than 8x.
"Jump forward" can be used instead (see playback keys).
- Rewind does not work properly. Sometimes enigma2 freezes when rewinding.
"Jump back" can be used instead (see playback keys).
- Some Samsung LCD TVs might have problems with the default resolution
576i.
- With "AC3 downmix on" there is no sound on optical when AC3 stream is
selected. With "AC3 downmix off" the system migt freeze when zapping to
channels with AC3.
- There are problems with switching between different satelleites via Diseqc.
It takes several seconds to tune to a channel on another satellite.
- Simultaneous output to HDMI and Scart is not supported.
- Sporadic hangers when zapping during an active HDTV recording
- Sporadic problems with old frames in a live stream (flashbacks)
- Some USB sticks are not recognized so that the Enigma2 installation
does not work. Reformatting the stick with FAT32 might help.
IMPORTANT:
When reporting problems please provide console logs documenting the system
behaviour.
DISCLAIMER
----------
The software is provided 'as is' without warranty of any kind.
Please consider that you may lose manufacturer's warranty when installing
this image.
This is an alpha image. That is some functions may not be available or be
buggy (causing crashes/freezes or loss of data).
The installation of the Enigma2 image formats (ext2) the internal harddisk
unless installation on a USB HDD is selected.
ALL FILES ON THE HARDDRIVE WILL BE LOST. When reverting the installation
on the internal HDD to the original Topfield firmware all Enigma2 files
will be lost too.
Installation instructions
-------------------------
You will need either a USB stick or a USB harddrive with FAT32 filesystem.
- Copy the files Enigma_Installer.tfd, uImage, rootfs.tar.gz and
Engima_Installer.ini to the USB device. Please read the instructions
in Engima_Installer.ini on how to modify the installation process.
- Attach the drive to the USB slot.
- Open the Topfield firmware update menu and select the image file
Enigma_Installer.tfd on the USB drive.
- Start the firmware update from USB. This part is very quick.
Restart the receiver when the display shows the blinking END
- After about 6-7 minutes the installation should be finished.
DO NOT REMOVE THE USB DEVICE UNTIL the INSTALLATION HAS FINISHED or
THE INSTALLER REQUESTS TO DETACH THE USB DEVICE.
- When installing to a USB HDD (option usbhdd in Enigma_Installer.tfd)
the installer will ask you to detach the initial USB device and to
attach a USB HDD to install to.
During the installation the VFD shows the current installation step and
error messages (if any):
"9 USB STCK" mounting USB stick
"STCK DETACH" waiting for USB device to be detached (USB HDD installation)
"HDD ATTACH" waiting for USB HDD to be attached (USB HDD installation)
"8 HDD PART" partitioning HDD
"7 HDD FMT" formatting HDD (root fs)
"6 HDD FMT" formatting HDD (data fs)
"5 HDD SWAP" creating swap
"4 ROOT FS" installing root file system
"3 LOADER" flashing U-Boot settings
"2 KERNEL" flashing kernel
"1 FSCK" checking file system
"0 REBOOT" rebooting within 2 seconds
When installing to a USB HDD the contents of the internal HDD remain unchanged.
IMPORTANT: When using the option "keepsettings" in Engima_Installer.ini the
newer settings (incl. keymap.xml updates) will not be installed.
It is recommended to attach a cable to the serial port and log the output in a
terminal program (e.g. TeraTerm, Putty) during the installation and the first
start. Serial port settings: 115200, 8, N, 1.
The USB filesystem should be writable to prevent infinite installation loop.
(The file uImage is renamed to avoid the infinite loop.)
The first start usually takes approximately 3 minutes due to creation of
device nodes.
To uninstall Enigma2, copy your favorite Topfield firmware on your stick and
rename it to "topfield.tfd" (don't forget to rename uImage_ if necessary). The
installer will flash the firmware and reboot the Toppy. There have been reports
that the PVR appears to be dead for about 5 minutes until the picture comes on
the TV screen. So please be patient. Enigma2 can also be removed by flashing a
regular Topfield firmware image using standard tools like TFD-Down or VegaPack
via the serial interface.
First start
-----------
On the first start the Enigma2 interactively configures the video output to be
used. The following options are available:
- Component
- HDMI
- Scart
- HDMI-PC
Each connection type is switched on for 30 seconds. The VFD displays the
connection type which is currently active. You can either wait until the
connection type you want is displayed and your TV shows a picture or you
can select the connection type with Up and Down buttons on the remote control.
Confirm the desired connection type with the Ok button. After that you can
proceed with the configuration supported by the configuration wizard.
The image contains a default channel table. If you want to replace it you can
perform a channel scan later.
Network configuration
---------------------
The U-Boot settings contain the following configuration by default:
MAC address 00:3e:9e:11:22:33
IP address 192.168.178.100
That is after booting the image you can login via telnet if your computer is in
the same subnet.
These values are set up by the U-Boot. You can change the values
in Enigma2 menu "Settings/System/Network.../Adapter settings".
Playback ****
-------------
Play - shows the file list
Pause - pauses playback or activates timeshift
Stop - stops playback or timeshift
Record - opens the record dialog for starting stopping recording
Yellow - pause/unpause playback
Green - continue playback
Red - jump to the beginning
Blue - jump to the next bookmark
1/3 jump 15 seconds backwards/forwards (configurable in the settings menu)
4/6 jump 60 seconds backwards/forwards (configurable in the settings menu)
7/9 jump 5 minutes backwards/forwards (configurable in the settings menu)
Full *** map can be found in the file /usr/local/share/enigma2/keymap.xml.
Team Ducktales
Changelog
---------
Version 0.3.2
---------------------------------------
+ Feature: added support for scrolling VDF strings
(settable with the command-line tool tffpctl)
+ Fix: fixed the issue with transponder blocked by a recording
Version 0.3.1
---------------------------------------
+ Feature: added support for the lower CI slot
+ Feature: more than 2 simultaneous recordings are possible
+ Feature: added VFD support for displaying some UTF-8 characters (ä, ö, ü)
+ Feature: added VFD support for displaying strings in upper case
(to display strings in lower and upper case comment out the line
"/bin/tffpctl --allcaps 1" in /etc/init.d/rcS)
+ Update: incorporated the new enigma2 version (05/30/2009)
+ Update: incorporated the new web interface version (06/04/2009)
+ Fix: disabled the HDD standby by default to avoid annoying spindowns/spinups
+ Fix: fixed the issue with multiple recordings on the same transponder
(timeshift also works while recording on the same transponder)
+ Fix: fixed fast forward for MP3 in MediaPlayer
+ Fix: increased the framebuffer memory to 12MB to allow HD skins
+ Fix: added missing file in Tuxtxt plugin
+ Fix: made timeshift start more stable
+ Fix: fixed mkv video with h264 or divx/xvid
+ Fix: reduced picture artifacts when browsing through e2 menus
Version 0.3.0
----------------------
+ Feature: introduced MediaPlayerExtended
+ Feature: timeshift is now working (still unstable). Press pause ***
to start timeshift and the stop *** to stop it. Alternatively
the timeshift may be stopped by switching to another channel.
+ Feature: added DHCP support
+ Change: mountpoint for sda3 is now set to /hdd (all programs recorded
before updating will appear after installation in /hdd instead of
/hdd/movies). The change was required to host timeshift files
on the sda3 (because they are created in /media/hdd).
+ Update: incorporated the new version of stmfb v22(37)[3.1]
+ Update: added new timezones
+ Fix: fixed displaying the Dolby icon on VFD
+ Fix: fixed the link status in the network menu
+ Fix: switched subtitle color to white
+ Fix: fixed the issue with stopping playback while it is paused
+ Fix: improved audio/video resynchronization after pause
+ Fix: improved CAM handling (especially the performance)
Version 0.2.1
----------------------
+ Fix: updated satellites.xml in /etc/tuxbox
+ Fix: changed the shutdown procedure to prevent corrupting the filesystem
+ Fix: fixed minor issues with tuxtxt
+ Fix: fixed minor issues in CAM handling
+ Fix: fixed the issue with e2 settings not saved during an update or
reinstallation
Version 0.2
-------------------------------------
+ Feature: first beta support for CAMs (upper slot only)
+ Feature: added flashing topfield.tfd (if present on the USB stick) to
make going back to Topfield firmware easier
+ Feature: freed 16 MB of unused RAM
+ Feature: migrated system partition to ext3 filesystem
+ Feature: migrated to stlinux-2.6.17.14-0041
+ Feature: installation control file (noformat, noupdate, nopartition,
keepsettings, usbhdd)
+ Feature: enabled installation to a USB HDD (option usbhdd)
+ Feature: improved emergency shutdown policy
+ Change: removed mapping of the **** V- (left) and V+ (right) to volume control
to avoid problems in various menus. The volume can now be adjusted with
the **** |< and >|.
+ Fix: the **** V-/V+ can now be used to change entries in the timer menu and
to scroll page up/page down.
+ Fix: updated the settings for Astra 19°° and added new satellites.xml for
orbital position 13.0, 19.2 and 23.5 east
+ Fix: applied the SATA patch to fix interactions with HDDs
+ Fix: fixed repeating Diseq commands delaying tuning up to 20 seconds
+ Fix: added swap to /etc/fstab
+ Fix: added the dvr1 device for recording
+ Fix: added updating the network settings to the rcS (activates the user
settings made in e2)
+ Fix: fixed the issue with "SID not found in PAT" and some scan problems
+ Fix: fixed the issue with low volume
+ Fix: improved shutdown behavior so that the PVR is not turned off before
the kernel finished unmounting file systems
+ Fix: updated Vader skin (DNS settings, timer)
+ Fix: swapped **** zapUp and zapDown
+ Fix: Daylight Saving Time
- Fix: no video on the FIRST start after installation
Version 0.1
-----------
* initial release
Hallo Leute..
Habe einpaar Fragen zu dem Topfield 7700HDPVR ohne Festplatte.
was für eine Festplatte wäre geeignet , Größe 500gb???
Lohnt es sich überhaupt enigma2 zu installieren???
kann man enigma2 ohne große Kenntnisse installieren ???
The only supported tuner type is DVB-S2 CX24116/CX24118
haben die Topfield 7700HDPVR verschiedene Tuner drin?
Danke im vorraus.
Topfield empfiehlt extra Platten was für TV Aufnahmen geeignet sind.
500GB ist ganz OK.
Das enigma2 kommt auf Festplatte da der flash zu klein ist.
ansonsten die enigm2 readme lesen. ja es gibt eigentlich nur die tuner typen .
ansonsten ist die Bedienung eben enigma2 ähnlich wie unter den dreamboxen.
mfg
würde so eine festplatte passen?
500GB Western Digital Caviar GP WD5000AACS
Zitat:
Zitat von haiput
Ne das ist keine CE/AV Festplatte. Sondern eine normale PC Festplatte.
Nimm die WD5000AVVS
mfg