Hallo,
ich muß jetzt mal eins meine D-Box 2 von Nokia selber flashen,mit Hallenberg.
Nun meine Frage an Euch reicht dafür ein Nullmodem Kabel!?
Druckbare Version
Hallo,
ich muß jetzt mal eins meine D-Box 2 von Nokia selber flashen,mit Hallenberg.
Nun meine Frage an Euch reicht dafür ein Nullmodem Kabel!?
Hi,
Du brauchst ein Croos-Over-Netzwerkkabel!
MfG schakal007
Also das Kabel mit dem ich mit der Box auch ins Net gehe!?
Nur mit Nullmodemkabel geht auch, ist aber ziemlich langwierig (Dies ist ein Link).
Die Pin-Belegung eines Crossoverkabel ist nicht identisch mit der eines normalen Patchkabels. Mit einem Crossoverkabel kannst du direkt von deiner Netzwerkkarte im PC die DBox connecten.
CU rqs
Ich habe nun noch zwei Kabel rumliegen,wie kann ich fesstellen ob eins davon ein Crossoverkabel ist!?
Das steht drauf! Sonst kauf eins-kosten doch nur ein paar Flocken!
Habe es zwar noch nie ausprobiert, aber mit einem normalen Netzwerkkabel -sofern ein Router oder Switch dazwischen hängt- sollte es doch auch gehen ?
Ja Linux ist schon drauf.Allerdings bleibt die Box beim Stat mit dem NG-Bild stehen.So das ich nicht FTP nutzen kann.Also zum Flashen brauch ich ein crossoverkabel und um die Box ins net zu bringen ein Netzwerkkabel!?
Und wie bekommt man raus ob man eine Box mit 1x oder 2x Chips hat? Muss man die dbox dazu zwingend aufschrauben? Falls ja, woran genau sieht man das ..?? werden ja wohl mehr als nur die 1 oder 2 Speicherchips auf der Platine sein...
... hier Bilder vom Innenleben der Nokia, kannst Du auch durch das Gehäuse sehen: hier ein link
Ich hab den Link für die Nokia in meinem 1. Post berichtigt. hier nochmals für Nokia
Nokia hat immer 2 x Intel. Nur die Sagem gibt es mit 1 x Intel bzw. 2 x Intel.
Bei einem normalen Patchkabel ist die Pinbelegung 1 zu 1 (Bild 1). In der Regel sind die Stecker transparent, du kannst die einzelnen Farben der twisted pair Verkabelung also sehen. Ist die Reihenfolge der Farben an beiden Steckern identisch, handelt es sich um ein normales Patchkabel. Bei einem Crossoverkabel sind Pin 1, 2, 3 und 6 über Kreuz verdrahtet (Bild 2).
CU rqs
Super, danke....dann brauch ich mir ja keinen Kopf machen. Da schon Neutrino drauf ist brauch ich auch keinen debug-mode mehr aktivieren. Also einfach ein 2x Image von Keywelt oder GLJ , per FTP ins /tmp legen und per dbox2-Menü das Image einspielen... Richtig?Zitat:
Nokia hat immer 2 x Intel. Nur die Sagem gibt es mit 1 x Intel bzw. 2 x Intel.
http://wiki.dbox2-tuning.net/wiki/in...ation:Neutrino
Hab die NIC runter auf 10 Halbdublex, Mediasensing für XP, boot.ini editiert auf eine CPU bis send komm ich im Bottmanager und auf den Befehl "enabled Debug mit minflash.txt" kommt das hier: Der Befehl "setenv TZ MET-01METDST-02,J84,J302" schlug fehl!
Woran liegt das denn jetzt noch? THX