nokia dbox2 boot problem

[ingobecker]

kann mir jemand helfen,habe glaube ich einen hardware defekt an meiner dbox2 nokia image kann ich einspielen beim hochfahren bleibt die box immer an der gleichen stelle hängen wenn ich die umschalttaste drücke bootet die box neu und bleibt danach wieder im standby modus hängen.

[Satfan123]

www.irata.de/service kann dir helfen wenn es nicht durch software zu lösen ist

prüfe aber mal zuerst ob der prozessor nicht glüht bzw. übermässig heiss wird

[Pandorra]

kann mir jemand helfen,habe glaube ich einen hardware defekt an meiner dbox2 nokia image kann ich einspielen beim hochfahren bleibt die box immer an der gleichen stelle hängen wenn ich die umschalttaste drücke bootet die box neu und bleibt danach wieder im standby modus hängen.

Moin,

poste doch mal ein Log.

MfG

Pandorra

[ingobecker]

Moin,
poste doch mal ein Log.
MfG
Pandorra
habe leider nicht viel ahnung habe die box vom profi in den debugmodus seten lassen war heute noch mal da er sagte keine fehler anzeige im log

[ingobecker]

wird nicht heiss

[Janek101Blau]

starte mal die Konsole - des bootmanagers dann die box danach einfach den Text von da kopieren und hier posten...

[ingobecker]

U-Boot 1.2.0 (Tuxbox) (Jun 13 2007 - 19:30:23)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .. done.
find_inode failed for name=boot.conf
load: Failed to find inode
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 669449 bytes loaded to 0x100000
.................................................. ............. done
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 669385 Bytes = 653.7 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.34-dbox2 (petze@linux) (gcc version 3.4.4) #2 Mi 13. Jun 20:06
:56 CEST 2007
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30824k available (1140k kernel code, 344k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1a:1a:b2
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00540000 : "root (squashfs)"
0x00540000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'lti-call
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Detected STB:
Vendor: Nokia
Model: D-BOX2
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: microcode verify: 5748 errors.
avia_av: timeout waiting for decoder init to complete. (00000001)
insmod: init_module: avia_av: Input/output error
insmod: unresolved symbol avia_av_set_stc
insmod: unresolved symbol avia_gt_gv_copyarea
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_get_blevel
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
insmod: unresolved symbol avia_gt_ir_exit
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_init
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
insmod: unresolved symbol avia_av_set_sample_rate
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_av_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
insmod: unresolved symbol avia_gt_pig_show
insmod: unresolved symbol avia_gt_pig_set_stack
insmod: unresolved symbol avia_gt_pig_set_size
insmod: unresolved symbol avia_gt_pig_set_pos
insmod: unresolved symbol avia_gt_pig_hide
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
insmod: unresolved symbol avia_av_stream_type_set
insmod: unresolved symbol avia_av_register_video_event_handler
insmod: unresolved symbol avia_av_set_audio_attenuation
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_av_pid_set
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_play_state_set_video
insmod: unresolved symbol avia_av_unregister_video_event_handler
insmod: unresolved symbol avia_av_get_video_size
insmod: unresolved symbol avia_av_play_state_set_audio
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_set_video_system
insmod: unresolved symbol avia_av_bypass_mode_set
insmod: unresolved symbol avia_av_sync_mode_set
insmod: unresolved symbol avia_gt_dmx_queue_nr_get_bytes_free
insmod: unresolved symbol avia_gt_dmx_get_ucode_info
insmod: unresolved symbol avia_gt_vbi_start
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol avia_av_napi_decoder_stop
insmod: unresolved symbol avia_gt_dmx_queue_stop
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_vbi_stop
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_framer
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_napi_decoder_start
insmod: unresolved symbol avia_gt_dmx_queue_start
insmod: unresolved symbol avia_gt_dmx_tap
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_enable_framer
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_dmx_get_stc
insmod: unresolved symbol avia_gt_accel_crc32
insmod: unresolved symbol avia_gt_napi_dvr_send
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_gt_set_playback_mode
insmod: unresolved symbol avia_gt_get_playback_mode
insmod: unresolved symbol avia_av_is500
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_cmd
Starting pid 91, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. Thu Jan 1 01:00:00 CET 1970
$Id: sectionsd.cpp,v 1.242 2007/06/10 19:28:48 houdini Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
/var/plugins/operations camdstart
[sectionsd] getUTC: open: No such file or directory
starte camd3

Starting pid 92, console /dev/console: '/bin/sh'


BusyBox v1.2.1 (2007.06.13-17:49+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ # [sectionsd] getUTC: open: No such file or directory
01.01.1970 01:00:04 camd3: BOXTYPE: 1
01.01.1970 01:00:04 camd3: LOG: 2
01.01.1970 01:00:04 camd3: UDP_PORT: 20248
01.01.1970 01:00:04 camd3: original slot au on
01.01.1970 01:00:04 camd3: HTTP_PORT: 9080
01.01.1970 01:00:04 camd3: DNS_CACHE: 600 sec
01.01.1970 01:00:04 camd3: SOCKET: /tmp/camd.sock01
01.01.1970 01:00:04 camd3: KEYS: /var/keys/camd3.keys
01.01.1970 01:00:04 camd3: SERVERS: /var/keys/camd3.servers
01.01.1970 01:00:04 camd3: USERS: /var/keys/camd3.users
01.01.1970 01:00:04 camd3: /dev/dvb/adapter0/ca1 No such file or directory
01.01.1970 01:00:04 camd3: UserDB(new): USER=benutzer1 PASS=password2 FROM=any S
ERVICES=any
01.01.1970 01:00:05 camd3: original slot: CAID=1702

01.01.1970 01:00:05 camd3: UserDB(new): USER=benutzer110 PASS=password10 FROM=an
y SERVICES=1702:000000:0008:0:0,1722:000000:0008:0:0 ,
01.01.1970 01:00:05 camd3: UserDB(update): USER=benutzer110 PASS=password10 FROM
=any SERVICES=1702:000000:0008:0:0,1722:000000:0008:0:0 ,
[sectionsd] getUTC: open: No such file or directory
01.01.1970 01:00:05 camd3: /var/keys/camd3.keys No such file or directory
01.01.1970 01:00:05 camd3: KeyDB: gestartet
01.01.1970 01:00:05 camd3: camd v3.868 - erfolgreich gestartet
01.01.1970 01:00:05 camd3: HTTP: started on port 9080
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
$Id: zapit.cpp,v 1.397 2007/06/10 19:36:49 houdini Exp $
[zapit] PMT update enabled
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
[frontend] uncommitted_switch_mode 0
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 11 onid 85
[getservices] dup transponder id 2 onid 85
[getservices] dup transponder id 4 onid 85
[getservices] dup transponder id 1 onid 85
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
/tmp/currentservices.xml: No such file or directory
[audio.cpp:CAudio:37] /dev/dvb/adapter0/audio0: No such file or directory
[video.cpp:CVideo:33] /dev/dvb/adapter0/video0: No such file or directory
[aviaext.cpp:CAViAext:37] /dev/dbox/aviaEXT: No such file or directory
$Id: controld.cpp,v 1.125 2006/09/24 09:17:10 barf Exp $

[sectionsd] getUTC: open: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld] /dev/dvb/adapter0/video0: No such file or directory
[controld] /dev/dvb/adapter0/video0: No such file or directory
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[sectionsd] getUTC: open: No such file or directory
[yhttpd] Webserver nhttpd/3.1.3 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...[sectionsd] getUTC: open: No such file or director
y

[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...

[Janek101Blau]

Muss nicht unbedingt was an der Hardware sein. Ich würde noch mal ein Flashreset versuchen eine anleitung steht http://wiki.tuxbox.org/MHC_2xIntel_bmon1.0
wenn sie 2 x Intelchips drauf hat sonst http://wiki.tuxbox.org/Flash_reset#Nokia_mit_2_x_AMD_Flash für AMD. Danach das image nochmal draufspielen. benutze dazu den assistenten...

[ingobecker]

woran erkenne ich ob ich 2x intel oder 2x amd habe