setup smargo on debian pc 5.0

[shane210585]

hallo i am installed debian server 5.0 on my pc.Everything had been done it as it showen in tutorial but my problem is my smargo donot show my card it
s++ ger##ny .i am trying it from last 1 week but till yet not success

[ 105.100007] usb 1-2: new full speed USB device using ohci_hcd and address 2
[ 105.312001] usb 1-2: configuration #1 chosen from 1 choice
[ 105.322035] usb 1-2: New USB device found, idVendor=0403, idProduct=6001
[ 105.322041] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 105.388002] usbcore: registered new interface driver usbserial
[ 105.388002] usbserial: USB Serial support registered for generic
[ 105.388002] usbcore: registered new interface driver usbserial_generic
[ 105.388002] usbserial: USB Serial Driver core
[ 105.432528] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 105.432551] ftdi_sio 1-2:1.0: FTDI USB Serial Device converter detected
[ 105.432575] ftdi_sio: Detected FT232BM
[ 105.432608] usb 1-2: FTDI USB Serial Device converter now attached to ttyUSB0
[ 105.432625] usbcore: registered new interface driver ftdi_sio
[ 105.432628] ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver


this what my pc show me by attaching smargo

my cfg setting

SERIAL READER : /dev/ttyUSB0 smartreader+

pls help me to resovle this problem.

[hansie45]

Try it with Protocol Mouse (NOT Smartreader, not internal)and dont try newer FTDI Driver (wont work).
On Ubuntu 9.04 al is running fine, on 9.10 nothing ist running, and one Difference is a new FTDI.

Also play with no mhz and no cardmhz and fixed Baudrate on Smargo, but only on Protocol Mouse.
Remember, if you one Time use Smartreader Protocol, you must remove your Smargo for to work again on Mouse Protocol! If you dont, no Card will be recogniced

[shane210585]

hi sir

as i told that i am using debian 5.0 server and what is Try it with Protocol Mouse how to do that i have no idee.pls help me further

[Fubbel]

hi,

what cardserver do u use? u set mouse in the reader section for the card.
mpcs.reader for example.

running debian 5.0.3 too and smargo in usb. runs fine for me. i use the x64 version if debian. but shouldn't make too much difference.

cu

[shane210585]

Hi i am zwing debian 5.0 Server edition 32 Bit and cccam on it
u had Said to setup Mouse , u meant in cfg or somewhere Else
bro it is possible to Backup ur Server then can i install it on
my pc my pc is also 64 b actually but i had trief 32b

[Fubbel]

won't make too much sense backing mine up.

i am using mpcs as cardserver by the way. not cccam server.

this option must be set in the cfg file yes. but as i never used cccam server i cannot tell u how exactly to change it for cccam server.

there is also a good howto for mpcs in the forum.

cu

[shane210585]

hi

ich hab ubuntu 9.04 server neu installiert und da lauft den smargo nix , der zeigt no card insterd , muss ich irgend welchen treibe1 runterladen damit der smargo die karte liest

[Fubbel]

nein.
normalerweise nicht. hab ich noch nie gehört....

hab mal was gelesen das jemand ubuntu 9.10 installiert hatte und das ganze nicht mehr ging. laut dieser person sei wohl ein neuer ftdi treiber schuld der bei ubuntu rein kam.
eventuell wird das bei der 9.04 per updates mit geupdated. eine klare aussage kann ich dazu aber nicht machen....

karte richtig im smargo drin?

ich würde mal testweise newcs, mpcs oder oscam probieren. nur die reader sektion für die karte einstellen und schauen was dieser sagt.

cccam habe ich leider zu wenig erfahrung was den serverteil betrifft.... :(

ich habe mittlerweile mehrere smargos. mein erster den ich hatte (eine ältere serie) hatte auch immer mal wieder das problem. card not inserted oder card not detected. kamen immer verschiedene meldungen. restart des cardservers hat das problem meist behoben. teilweise hat es aber 2-4 restarts gebraucht.
seit dem ich die derzeit neueste serie des smargos habe kann ich dieses problem bei mir nicht mehr reproduzieren.

ansonsten damit du mehr hilfe bekommst bräuchte man mal die logs und configs. vllt weiß ja noch jemand was zum cccam server.
ansonsten würde ich sowieso eher zu newcs, mpcs oder oscam raten.

mfg

[shane210585]

hi

[Fubbel]

sorry but i don't understand too much now u wrote....

maybe writing in english directly would be more accurate instead of translating trough google or something.

[shane210585]

yesterday i had installed ubuntu 9.04 without update ,installing CC.x86 and cfg.
it had worked till next reboot and after that it has not detect card.but when i give -d command it show me nds card at very first time.then does not detect the card.

i have athlon 1.8 ghz with 512 mb ram.
some has told me that i need to buy a new pc with atom and ram must upper then 2 gb then it will work like charm

[Fubbel]

hi,
curious problem u got...

i dont think its a problem of the hardware. other people run their card in a dbox2 oder in a dreambox. these, especially the dbox2 have much less performance than a pc hardware. also detecting the card shouldn't make any trouble with your hardware.
my hardware spec is a lot higher. intel dual core 2ghz overclocked to 2,66 with 2gb ram. will switch too other hardware soon which is stronger again, but still in setting it up. (again debian 5.0.3)

as a wrote before maybe thats a prob of the smargo u got. i had similar problems with the older smargo version too that detecting the card was not possible. or it was detected but mpcs said unsupported card system. without touching the smargo or the card restarting mpcs a few times (mostly 2-4) solved the problem. with the new smargo version (see argolis.com for design) i haven't recognized the problem.

maybe u can also set your smargo to auto recognize the card mhz and so on. or try fixing the mhz with the smargo software. nds has 3.57mhz i think. but recheck that again!!!

i also read that there are fake smargo's around. maybe also that is your problem.

u have any possibilities to check your card in a dreambox directly? maybe your card makes problems.

best ways in my opinion, or what i would do...
- post configs and total log outputs here
- check card in other reader. best would be not in smargo.
- if card runs in a dreambox. check card with smargo in the dreambox or some other box
- also i would try reading the card on linux server or some other hardware with other cardserver such as newcs, mpcs or oscam.

i think all other ways won't make too much sense. u have to try in some other setup. after u reinstalled i don't think its a software problem of your linux system.

most easiest way is probably setting up a newcs or mpcs and try with them.

good luck..

[shane210585]

hi bro

thzanks alot that ur giving such a goledn time for me.i had tried it on my dm 800 with smargo it work like a charm; IT JUST MAKE PROBLEM with my pc
tommorow i am going to buy a new pc with atom.
###############################################
##### #####
### Config File Created by Cam-Editor ###
### Cam-Editor ©2006-2007 Oermens ###
##### CCcam-Editor 2.0.0 #####
###############################################
#### Thanks ####
#### CCcam team uvadi ####
###############################################
#### Friends ####
###############################################
# #

# #
###############################################
#### Servers ####
###############################################
# #
#

# #
###############################################
#### Config ####
###############################################
# SERVER LISTEN PORT : #
SERVER LISTEN PORT : 12000
# ALLOW TELNET INFO : #
ALLOW TELNETINFO: yes
# ALLOW WEB INFO : #
ALLOW WEBINFO: yes
# WEBINFO USERNAME : #
WEBINFO USERNAME :
# WEBINFO PASSWORD : #
WEBINFO PASSWORD :
# TELNETINFO USERNAME : #
TELNETINFO USERNAME :
# TELNETINFO PASSWORD : #
TELNETINFO PASSWORD :
# TELNET INFO LISTEN PORT : #
TELNETINFO LISTEN PORT : 16000
# WEB INFO LISTEN PORT : #
WEBINFO LISTEN PORT : 16001
# ZAP OSD TIME : #
ZAP OSD TIME :5
# OSD USERNAME : #
OSD USERNAME :root
# OSD PASSWORD : #
OSD PASSWORD :dreambox
# OSD PORT : #
OSD PORT :80
# SERIAL READER : #
# SMARTCARD WRITE DELAY : #
# SMARTCARD CLOCK FREQUENCY #
#SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 3570000
# EMM Blocker #
# SHOW TIMING : #
SHOW TIMING : yes
# DEBUG : #
DEBUG : yes
# NEWCAMD CONF : #
NEWCAMD CONF :no
# DISABLE EMM : #
DISABLE EMM : no
# EXTRA EMM LEVEL : #
EXTRA EMM LEVEL : yes
# Mini OSD #
MINI OSD : yes
# CAM KEY #
# CAMDATA #
#BOXKEY: /dev/ttyUSB0 XX XX XX XX
#B: /dev/ttyUSB0 00
# BEEF ID : #
# PIN : #
# SOFTKEY FILE : #
SOFTKEY FILE : /var/keys/SoftCam.Key
# AUTOROLL FILE : #
AUTOROLL FILE : /var/keys/AutoRoll.Key
# STATIC CW FILE : #
STATIC CW FILE : /var/etc/CCcam.channelinfo
# CAID PRIO FILE : #
CAID PRIO FILE : /var/etc/CCcam.providers
# LOG WARNINGS : #
LOG WARNINGS : /tmp/warnings.txt
# PROVIDERINFO FILE : #
PROVIDERINFO FILE : /var/etc/CCcam.providers
# CHANNELINFO FILE : #
CHANNELINFO FILE : /var/etc/CCcam.channelinfo

# #
# LOADBALANCE : #
# TRY ALL CHIDS : #
SERIAL READER: /dev/ttyUSB0 smartreader+

# POSTINIT : #
# DVB API : #
#DVB API: -1
# #
# SHOW EXTENEDED CLIENT INFO : #
# EMM THREADS : #
# MINIMUM DOWNHOPS : #
MINIMUM DOWNHOPS: 0
# #
###############################################
####### Enjoy #######
###############################################

# POSTINIT : #
# DVB API : #
# #
###############################################
####### Enjoy #######
###############################################

[ 306.980019] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 308.270013] usb 1-1: new full speed USB device using ohci_hcd and address 3
[ 308.487343] usb 1-1: configuration #1 chosen from 1 choice
[ 308.549553] USB Serial support registered for FTDI USB Serial Device
[ 308.549605] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
[ 308.549660] usb 1-1: Detected FT232BM
[ 308.549750] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0
[ 308.549769] usbcore: registered new interface driver ftdi_sio
[ 308.549772] ftdi_sio: v1.4.3:USB FTDI Serial Converters Driver
[ 313.822576] ftdi_sio ttyUSB0: error from flowcontrol urb
[ 314.056129] usb 1-1: USB disconnect, address 3
[ 314.056412] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[ 314.056428] ftdi_sio 1-1:1.0: device disconnected
[ 315.990013] usb 1-2: new full speed USB device using ohci_hcd and address 4
[ 316.207736] usb 1-2: configuration #1 chosen from 1 choice
[ 316.210745] ftdi_sio 1-2:1.0: FTDI USB Serial Device converter detected
[ 316.210778] usb 1-2: Detected FT232BM
[ 316.210855] usb 1-2: FTDI USB Serial Device converter now attached to ttyUSB0
[ 321.481314] usb 1-2: USB disconnect, address 4
[ 321.481610] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[ 321.481626] ftdi_sio 1-2:1.0: device disconnected
[ 322.210013] usb 1-2: new full speed USB device using ohci_hcd and address 5
[ 322.427643] usb 1-2: configuration #1 chosen from 1 choice
[ 322.430663] ftdi_sio 1-2:1.0: FTDI USB Serial Device converter detected
[ 322.430699] usb 1-2: Detected FT232BM
[ 322.430777] usb 1-2: FTDI USB Serial Device converter now attached to ttyUSB0

00:57:04.287 CCcam: online using nodeId 54988956bdcfda27
00:57:04.289 CCcam: create 1 cam device(s)
00:57:07.330 CCcam: nds card found
00:57:10.333 CCcam: card init fail
00:57:10.333 CCcam: readKeyfile: cannot open /var/keys/SoftCam.Key or not found
00:57:10.333 CCcam: readKeyfile: cannot open /var/keys/AutoRoll.Key or not found
00:57:10.333 CCcam: static cw not found or bad
00:57:10.334 CCcam: parsed 0 entries from /var/etc/CCcam.providers
00:57:10.334 CCcam: readProviderfile: cannot open /var/etc/CCcam.providers or not found
00:57:10.334 CCcam: readChannelList: cannot open /var/etc/CCcam.channelinfo or not found
00:57:10.334 CCcam: server started on port 12000
00:57:11.027 CCcam: card detect fail
00:57:12.936 CCcam: card detect fail
00:57:14.238 CCcam: card detect fail
00:57:16.199 CCcam: card detect fail